Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0347    Camshaft Position Sensor "A" Circuit Low Input (Bank 2)

DTC    P0348    Camshaft Position Sensor "A" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The VVT sensor (VV1, VV2 signal) consists of a magnet and MRE (Magnetic Resistance Element).
The VVT camshaft timing gear assembly has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affect the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each engine revolution. Based on the combination of the VVT sensor signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No.
DTC Detection Condition
Trouble Area
P0340
  1. Either of following conditions is met:
  1. No VVT sensor signal to ECM while cranking. (2 trip detection logic)
  2. Missing VVT sensor signal despite crankshaft position sensor signal input normal at engine speed of 600 rpm or more. (1 trip detection logic)
  1. Open or short in VVT sensor (bank 1, 2) circuit
  2. VVT sensor (bank 1, 2)
  3. Camshaft timing gear assembly
  4. Jumped tooth of timing chain
  5. ECM
P0342
P0347
Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
  1. Open or short in VVT sensor (bank 1, 2) circuit
  2. VVT sensor (bank 1, 2)
  3. ECM
P0343
P0348
Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
  1. Open or short in VVT sensor (bank 1, 2) circuit
  2. VVT sensor (bank 1, 2)
  3. ECM
P0345
No VVT sensor signal to ECM at engine speed 600 rpm or more. (1 trip detection logic)
  1. Open or short in VVT sensor (bank 1, 2) circuit
  2. VVT sensor (bank 1, 2)
  3. Camshaft timing gear assembly
  4. Jumped tooth of timing chain
  5. ECM

  1. G035795E10
  2. Inspection using an oscilloscope

    HINT:
    1. The correct waveform is shown above.
    2. VV1 and VV2 stand for the VVT sensor signal, and NE stands for the crank angle sensor plate does not have any cracks or deformation. sensor signal.
      Item
      Content
      Terminal
      NE+ - NE-
      VV1+ - VV1-
      VV2+ - VV2-
      Equipment Setting
      5 V/DIV, 20 ms/DIV,
      Condition
      Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.
When the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (bank 1) verify pulse input
P0340: Camshaft position/Crankshaft position misalignment (bank 1)
P0342: VVT sensor (bank 1) range check (low voltage)
P0343: VVT sensor (bank 1) range check (high voltage)
P0345: VVT sensor (bank 2) verify pulse input
P0347: VVT sensor (bank 2) range check (low voltage)
P0348: VVT sensor (bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT sensors (bank 1, 2)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
4 seconds:
P0340 (VVT sensor (bank 1) verify pulse input (case 2))
P0342 and P0347 (VVT sensor (bank 1, 2) range check (low voltage))
P0343 and P0348 (VVT sensor (bank 1, 2) range check (high voltage))
5 seconds:
P0340 (VVT sensor (bank 1) verify pulse input (case 1))
P0345 (VVT sensor (bank 2) verify pulse input)
MIL Operation
2 driving cycles:
P0340 (VVT sensor (bank 1) verify pulse input (case 2)
Immediate:
Others
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
None

P0340 VVT Sensor (Bank 1) Verify Pulse Input (Case 1) 
All of the following conditions are met
-
Engine speed
600 rpm or more
Starter
OFF
VVT system misalignment
Not detected
VVT sensor range check fail (P0342, P0343)
Not detected
VVT sensor voltage
0.3 to 4.7 V

P0340: VVT Sensor (Bank 1) Verify Pulse Input (Case 2) 
Both of the following conditions are met
-
Starter
ON
Minimal battery voltage while starter ON
Less than 11 V

P0342 and P0343: VVT Sensor (Bank 1) Range Check 
All of the following conditions are met
-
Starter
OFF
Ignition switch
ON
Time after ignition switch OFF to ON
2 seconds or more
VVT sensor pulse input fail (P0340)
Not detected
Battery voltage
8 V or higher

P0345: VVT Sensor (Bank 2) Verify Pulse Input 
All of the following conditions are met
-
Engine speed
600 rpm or more
Starter
OFF
VVT sensor range check fail (P0342, P0343, P0347, P0348)
Not detected
VVT sensor voltage
0.3 to 4.7 V
Battery voltage
8 V or more
Ignition switch
ON
Time after ignition switch off to ON
More than 0.5 seconds

P0347 and P0348: VVT Sensor (Bank 2) Range Check 
All of the following conditions are met
-
Starter
OFF
Ignition switch
ON
Time after ignition switch OFF to ON
2 seconds or more
VVT sensor verify pulse input fail (P0340, P0345)
Not detected
Battery voltage
8 V or higher

TYPICAL MALFUNCTION THRESHOLDS


P0340: VVT Sensor (Bank 1) Verify Pulse Input (Case 1) 
Either of the following conditions is met
1 or 2
1. VVT and crankshaft position alignment
Misalignment
2. VVT sensor signal
No signal

P0340 and P0345: VVT Sensor (Bank 1, 2) Verify Pulse Input (Case 2) 
VVT sensor signal
No signal

P0342 and P0347: VVT Sensor (Bank1, 2) Range Check (Low Voltage) 
VVT sensor voltage
Less than 0.3 V

P0343 and P0348: VVT Sensor (Bank1, 2) Range Check (High voltage) 
VVT sensor voltage
More than 4.7 V

COMPONENT OPERATING RANGE


VVT sensor voltage
0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK VVT SENSOR (SENSOR POWER SOURCE)
A193258E06
  1. Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    V6-3 (VC) - Body ground
    Always
    4.5 to 5.5 V
    V5-3 (VC) - Body ground
    Always
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Front view of wire harness connector
    (to VVT Sensor)



NG
Go to step 8
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    V6-1 (VVR+) - E9-9 (VV1+)
    Always
    Below 1 Ω
    V5-1 (VVL+) - E9-12 (VV2+)
    Always
    Below 1 Ω
    V6-2 (VVR-) - E9-10 (VV1-)
    Always
    Below 1 Ω
    V5-2 (VVL-) - E9-11 (VV2-)
    Always
    Below 1 Ω
    V6-1 (VVR+) or E9-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    V5-1 (VVL+) or E9-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    V6-2 (VVR-) or E9-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    V5-2 (VVL-) or E9-11 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR)
BR03795E25
  1. Check the VVT sensor installation.

    OK:
    VVT sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR
OK


4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH PLATE)
  1. Inspect the teeth of the sensor plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
  1. Remove the cylinder head cover (Click here and Click here).



    A237949E01
  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) to align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *a
    Bank 1
    *b
    Bank 2
    *c
    Timing Mark



NG
ADJUST VALVE TIMING
OK


6.REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (P0340, P0342, P0343, P0345, P0347 OR P0348)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END 

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    V6-3 (VC) - E9-15 (VCV1)
    Always
    Below 1 Ω
    V5-3 (VC) - E9-16 (VCV2)
    Always
    Below 1 Ω
    V6-3 (VC) or E9-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    V5-3 (VC) or E9-16 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)