Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0722    Output Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The speed sensor (SP2) detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals.
An AC voltage is generated in the speed sensor (SP2) coil as the rotor mounted on the output shaft rotates, and this voltage is sent to the ECM.
The gear shift point and lock-up timing are controlled by the ECM based on the signals from the speed sensor and the throttle position sensor.

DTC No.
DTC Detection Condition
Trouble Area
P0722
All conditions below are detected 500 times or more continuously. (2-trip detection logic)
(a) No signal from speed sensor SP2 is input to the ECM.
(b) Vehicle speed is 9 km/h (5.59 mph) or more.
  1. Open or short in speed sensor (SP2) circuit
  2. Speed sensor (SP2)
  3. ECM

Reference (Using an oscilloscope):
Check the waveform between terminals SP2+ and SP2- of the ECM connector.
G020664E05

Standard:
Refer to the illustration.
Item
Content
Terminal
SP2+- SP2-
Tool setting
2 V/DIV
20 ms/DIV
Vehicle condition
Vehicle speed 20 km/h (12 mph)


MONITOR DESCRIPTION

The output speed sensor (SP2) monitors the output shaft speed. The ECM controls the gear shift point and the lock-up timing based on the signals from the output speed sensor (SP2) and throttle position sensor.
If the ECM detects no signal from the output speed sensor (SP2) even while the vehicle is moving, it will conclude that there is a malfunction in the output speed sensor (SP2). The ECM will illuminate the MIL and set the DTC.

MONITOR STRATEGY


Related DTCs
P0722: Speed sensor SP2/Verify pulse input
Required sensors/Components
Speed sensor SP2
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
Vehicle speed from vehicle speed sensor
9 km/h (5.59 mph) or more

TYPICAL MALFUNCTION THRESHOLDS


Speed sensor signal
No signal

COMPONENT OPERATING RANGE


Vehicle speed from vehicle speed sensor
9 km/h (5.59 mph) or more

WIRING DIAGRAM


C124517E06


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
According to the Data List displayed by Techstream, you can read the values of switches, sensors, actuators and so on without removing parts. Reading the Data List as the first step of troubleshooting is one method to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Turn the ignition switch ON, and turn the tester main switch ON.
  7. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
  8. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -

    HINT:
    1. SPD (SP2) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. The SPD (SP2) value displayed on the tester is much lower than the actual vehicle speed:
      Sensor trouble, improper installation, or intermittent connection trouble in the circuit.

1.INSPECT SPEED SENSOR INSTALLATION
BR03795E01
  1. Check the speed sensor (SP2) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
REPLACE SPEED SENSOR (SP2) (Click here)
OK


2.INSPECT SPEED SENSOR (SP2)
C110343E20
  1. Disconnect the speed sensor connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    560 to 680 Ω at 20°C (68°F)



NG
REPLACE SPEED SENSOR (SP2) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR - ECM)
C095812E38
  1. Connect the speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    E5-35 (SP2+) - E5-27 (SP2-)
    560 to 680 Ω at 20°C (68°F)
    E5-35 (SP2+) - Body ground
    10 kΩ or higher
    E5-27 (SP2-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)