DTC B1780 Front Occupant Classification Sensor LH Circuit Malfunction |
| DTC No. | DTC Detecting Conditions | Trouble Areas |
| B1780 |
|
|

| 1.CHECK DTC |
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the occupant classification sensor front LH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Check that the connectors (on the occupant classification ECU side and occupant classification sensor front LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK NO. 1 SEAT WIRE (TO B+) |
![]() |
Disconnect the connectors from the occupant classification ECU and the occupant classification sensor front LH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| O4-1 (SGD1) - Body ground | Ignition switch ON | Below 1 V |
| O4-7 (SIG1) - Body ground | Ignition switch ON | Below 1 V |
| O4-11 (SVC1) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK NO. 1 SEAT WIRE (FOR OPEN) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using service wires, connect O6-1 (SVC1) and O6-3 (SGD1), and connect O6-2 (SIG1) and O6-3 (SGD1) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| O4-7 (SIG1) - O4-1 (SGD1) | Always | Below 1 Ω |
| O4-11 (SVC1) - O4-1 (SGD1) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK NO. 1 SEAT WIRE (FOR SHORT) |
![]() |
Disconnect the service wires from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| O4-7 (SIG1) - O4-1 (SGD1) | Always | 1 MΩ or higher |
| O4-11 (SVC1) - O4-1 (SGD1) | Always | 1 MΩ or higher |
| O4-7 (SIG1) - O4-11 (SVC1) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK NO. 1 SEAT WIRE (TO GROUND) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| O4-1 (SGD1) - Body ground | Always | 1 MΩ or higher |
| O4-7 (SIG1) - Body ground | Always | 1 MΩ or higher |
| O4-11 (SVC1) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK DTC |
Connect the connectors to the occupant classification ECU and the occupant classification sensor front LH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| NG | |
| 9.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 10.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position.
Using the Techstream, perform the zero point calibration (Click here).
|
| ||||
| OK | |
| 11.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
|
| ||||
| OK | |
| 12.CHECK DTC |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| NG | |
| 13.REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY RH |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat with adjuster frame assembly RH (Click here).
| NEXT | |
| 14.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 15.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
| NEXT | ||
| ||