Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM (for Separate Seat Type)

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The center airbag sensor assembly communication circuit consists of the occupant classification ECU and the center airbag sensor assembly.
DTC B1790 is set when a malfunction is detected in the center airbag sensor assembly communication circuit.

DTC No.
DTC Detections Conditions
Trouble Areas
B1790
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the center airbag sensor assembly communication circuit for 2 seconds
  2. Center airbag sensor assembly malfunction
  3. Occupant classification ECU malfunction
  1. Floor wire
  2. No. 1 seat wire
  3. Occupant classification ECU
  4. Center airbag sensor assembly

HINT:
  1. When DTC B1630/32 is detected as a result of troubleshooting the supplemental restraint system, perform troubleshooting for DTC B1790 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


H101477E05


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of the Techstream probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad assembly.
  5. (e) Disconnect the connector from the front passenger airbag assembly.

HINT:
Skip the following steps if side and curtain shield airbags are not fitted.

  1. (f) Disconnect the connector from the front seat airbag assembly LH.
  2. (g) Disconnect the connector from the front seat airbag assembly RH.
  3. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  4. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  5. (j) Disconnect the connector from the front seat outer belt assembly LH.
  6. (k) Disconnect the connector from the front seat outer belt assembly RH.

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat assembly installation bolts to see the under surface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK DTC
  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

HINT:
  1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

HINT:
DTCs other than B1790 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECT CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and occupant classification ECU side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (FOR OPEN)


    H100212E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect O5-8 (FSR+) and O5-4 (FSR-) of connector E.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - A23-13 (FSP-)
    Always
    Below 1 Ω



NG
Go to step 13
OK


5.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (FOR SHORT)


    H100211E01
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - A23-13 (FSP-)
    Always
    1 MΩ or higher



NG
Go to step 14
OK


6.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (TO B+)


    H100211E01
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - Body ground
    Ignition switch ON
    Below 1 V
    A23-13 (FSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 15
OK


7.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (TO GROUND)


    H100211E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - Body ground
    Always
    1 MΩ or higher
    A23-13 (FSP-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 16
OK


8.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

HINT:
  1. First clear any DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

HINT:
DTCs other than B1790 may be output at this time, but they are not related to this check.



NG
USE SIMULATION METHOD TO CHECK
NG


9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed on the Techstream.


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT


12.CHECK DTC
  1. Connect the connector to the occupant classification ECU.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

HINT:
  1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

HINT:
DTCs other than B1790 may be output at this time, but they are not related to this check.



NG
REPLACE AIRBAG SENSOR ASSEMBLY CENTER
OK

END 

13.CHECK NO. 1 SEAT WIRE (FOR OPEN)


    H101916E01
  1. Disconnect the No.1 seat wire connector from the occupant classification ECU.

HINT:
The service wire has already been inserted into connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSP+) - BH1-6 (FSP-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

14.CHECK NO. 1 SEAT WIRE (FOR SHORT)


    H046144E02
  1. Disconnect the No.1 seat wire connector from the occupant classification ECU.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSP+) - BH1-6 (FSP-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

15.CHECK NO. 1 SEAT WIRE (TO B+)


    H046144E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the No. 1 seat wire connector from the occupant classification ECU.

  1. Disconnect the connector from the occupant classification ECU.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSP+) - Body ground
    Ignition switch ON
    Below 1 V
    BH1-6 (FSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

16.CHECK NO. 1 SEAT WIRE (TO GROUND)


    H046144E02
  1. Disconnect the No. 1 seat wire connector from the occupant classification ECU.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSP+) - Body ground
    Always
    1 MΩ or higher
    BH1-6 (FSP-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE