Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1620/21    Driver Side - Side Airbag Sensor Circuit Malfunction

DTC    B1625/22    Front Passenger Side - Side Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor assembly LH consists of parts such as the safing sensor, the diagnostic circuit and the lateral deceleration sensor. The configuration of the side airbag sensor assembly RH is the same as that of the LH.
When the airbag sensor assembly center receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1620/21 is set when a malfunction is detected in the side airbag sensor assembly (driver seat side) circuit.
DTC B1625/22 is set when a malfunction is detected in the side airbag sensor assembly (front passenger seat side) circuit.

DTC No.
DTC Detecting Conditions
Trouble Areas
B1620/21
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side airbag sensor assembly (Driver seat side) circuit for 2 seconds
  2. Side airbag sensor assembly LH malfunction
  3. Rear airbag sensor LH malfunction
  4. Center airbag sensor assembly malfunction
  1. Side airbag sensor assembly LH
  2. Rear airbag sensor LH
  3. Center airbag sensor assembly
  4. No. 2 floor wire
B1625/22
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side airbag sensor assembly (Front passenger seat side) circuit for 2 seconds
  2. Side airbag sensor assembly RH malfunction
  3. Rear airbag sensor RH malfunction
  4. Center airbag sensor assembly malfunction
  1. Side airbag sensor assembly RH
  2. Rear airbag sensor RH
  3. Center airbag sensor assembly
  4. Floor wire

WIRING DIAGRAM


H101817E03


INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. Check the DTC (Click here).

      Result:
      Result
      Proceed to
      DTC B1620/21 is output.
      A
      DTC B1625/22 is output.
      B
      DTC B1620/21 and B1625/22 are output.
      C
      Neither DTC B1620/21 nor B1625/22 is output.
      D



B
Go to step 17

C
Go to step 32

D
USE SIMULATION METHOD TO CHECK
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK NO. 2 FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101478E01
  1. Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly LH.

  1. Using SST, connect S11-4 (BBL+) and S11-3 (BBL-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - A22-15 (BBD-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK NO. 2 FLOOR WIRE (FOR SHORT)


    H100839E08
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - A22-15 (BBD-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


6.CHECK NO. 2 FLOOR WIRE (TO B+)


    H100839E08
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - Body ground
    Ignition switch ON
    Below 1 V
    A22-15 (BBD-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


7.CHECK NO. 2 FLOOR WIRE (TO GROUND)


    H100839E06
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - Body ground
    Always
    1 MΩ or Higher
    A22-15 (BBD-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


8.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    H100840E03
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn any ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

Result:
Result
Proceed to
DTC B1620/21 is output.
A
DTC B1625/22 is output.
B
Neither DTC B1620/21 nor B1625/22 is output.
C



B
REPLACE REAR AIRBAG SENSOR LH

C
USE SIMULATION METHOD TO CHECK
A


9.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


10.CHECK CONNECTORS
  1. Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


11.CHECK NO. 2 FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E01
  1. Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.

  1. Using SST, connect S13-1 (BCL-) and S13-2 (BCL+) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


12.CHECK NO. 2 FLOOR WIRE (FOR SHORT)


    H101480E01
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


13.CHECK NO. 2 FLOOR WIRE (TO B+)


    H101480E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    S11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


14.CHECK NO. 2 FLOOR WIRE (TO GROUND)


    H101480E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Always
    1 MΩ or Higher
    S11-2 (BCL-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


15.CHECK DTC


    H100929E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1620/21 is not output.

HINT:
DTCs other than B1620/21 may be output at this time, but they are not related to this check.



OK
REPLACE REAR AIRBAG SENSOR LH
NG


16.REPLACE CENTER AIRBAG SENSOR ASSEMBLY


    H100929E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    B1620/21 is not output.

HINT:
DTCs other than B1620/21 may be output at this time, but they are not related to this check.



NG
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH
OK

END 

17.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


18.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


19.CHECK FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H100941E01
  1. Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly RH.

  1. Using SST, connect S12-4 (BBR+) and S12-3 (BBR-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - A23-11 (BBP-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


20.CHECK FLOOR WIRE (FOR SHORT)


    H100846E04
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - A23-11 (BBP-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


21.CHECK FLOOR WIRE (TO B+)


    H100846E04
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - Body ground
    Ignition switch
    Below 1 V
    A23-11 (BBP-) - Body ground
    Ignition switch
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


22.CHECK FLOOR WIRE (TO GROUND)


    H100846E04
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - Body ground
    Always
    1 MΩ or Higher
    A23-11 (BBP-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


23.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    H100847E03
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

Result:
Result
Proceed to
DTC B1625/22 is output.
A
DTC B1620/21 is output.
B
Neither DTC B1620/21 nor B1625/22 is output.
C



B
REPLACE REAR AIRBAG SENSOR RH

C
USE SIMULATION METHOD TO CHECK
A


24.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


25.CHECK CONNECTORS
  1. Check that the connectors (on the side airbag sensor assembly RH side and rear airbag sensor RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


26.CHECK FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E03
  1. Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.

  1. Using SST, connect S14-1 (BCR-) and S14-2 (BCR+) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


27.CHECK FLOOR WIRE (FOR SHORT)


    H101480E02
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


28.CHECK FLOOR WIRE (TO B+)


    H101480E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    S12-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


29.CHECK FLOOR WIRE (TO GROUND)


    H101480E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Always
    1 MΩ or Higher
    S12-2 (BCR-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


30.CHECK DTC


    H100201E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1625/22 is not output.

HINT:
DTCs other than B1625/22 may be output at this time, but they are not related to this check.



OK
REPLACE REAR AIRBAG SENSOR RH
NG


31.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    H100201E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1625/22 is not output.

HINT:
DTCs other than B1625/22 may be output at this time, but they are not related to this check.



NG
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH
OK

END 

32.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


33.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


34.CHECK NO. 2 FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101478E01
  1. Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly LH.

  1. Using SST, connect S11-4 (BBL+) and S11-3 (BBL-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - A22-15 (BBD-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


35.CHECK NO. 2 FLOOR WIRE (FOR SHORT)


    H100839E15
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - A22-15 (BBD-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


36.CHECK NO. 2 FLOOR WIRE (TO B+)


    H100839E15
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - Body ground
    Ignition switch ON
    Below 1 Ω
    A22-15 (BBD-) - Body ground
    Ignition switch ON
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


37.CHECK NO. 2 FLOOR WIRE (TO GROUND)
  1. Turn the ignition switch to the LOCK position.



    H100839E15
  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-8 (BBD+) - Body ground
    Always
    1 MΩ or Higher
    A22-15 (BBD-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


38.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


39.CHECK CONNECTORS
  1. Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


40.CHECK NO. 2 FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E01
  1. Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.

  1. Using SST, connect S13-1 (BCL-) and S13-2 (BCL+) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


41.CHECK NO. 2 FLOOR WIRE (FOR SHORT)


    H101480E01
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


42.CHECK NO. 2 FLOOR WIRE (TO B+)


    H101480E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 Ω
    S11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


43.CHECK NO. 2 FLOOR WIRE (TO GROUND)


    H101480E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Always
    1 MΩ or Higher
    S11-2 (BCL-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


44.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


45.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


46.CHECK FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H100941E01
  1. Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly RH.

  1. Using SST, connect S12-4 (BBR+) and S12-3 (BBR-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - A23-11 (BBP-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


47.CHECK FLOOR WIRE (FOR SHORT)


    H100846E04
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - A23-11 (BBP-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


48.CHECK FLOOR WIRE (TO B+)


    H100846E04
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - Body ground
    Ignition switch ON
    Below 1 V
    A23-11 (BBP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


49.CHECK FLOOR WIRE (TO GROUND)


    H100846E04
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-8 (BBP+) - Body ground
    Always
    1 MΩ or Higher
    A23-11 (BBP-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


50.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


51.CHECK CONNECTORS
  1. Check that the connectors (on the side airbag sensor assembly RH side and rear airbag sensor RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


52.CHECK FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E03
  1. Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.

  1. Using SST, connect S14-1 (BCR-) and S14-2 (BCR+) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


53.CHECK FLOOR WIRE (FOR SHORT)


    H101480E02
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


54.CHECK FLOOR WIRE (TO B+)


    H101480E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    S12-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


55.CHECK FLOOR WIRE (TO GROUND)


    H101480E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Always
    1 MΩ or Higher
    S12-2 (BCR-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


56.CHECK DTC


    H100202E01
  1. Connect the connectors to the center airbag sensor assembly and side airbag sensor assembly.

NOTICE:
Do not connect the rear airbag sensor LH and the rear airbag sensor RH connector.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1620/21 and B1625/22 are not output.

HINT:
DTCs other than B1620/21 and B1625/22 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR LH AND REAR AIRBAG SENSOR RH
OK


57.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    H100202E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the rear airbag sensor LH and the rear airbag sensor RH.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1620/21 and B1625/22 are not output.

HINT:
DTCs other than B1620/21 and B1625/22 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR LH AND REAR AIRBAG SENSOR RH
OK

END