Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1655/37    Driver Side Seat Belt Buckle Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and the front seat inner belt assembly LH (seat belt buckle switch LH).
DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch (driver seat side) circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1655/37
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch (Driver seat side) circuit for 2 seconds
  2. Front seat inner belt assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. No. 1 seat wire*1
  3. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  4. Center airbag sensor assembly
*1: for Bench Seat Type

WIRING DIAGRAM


C190118E02


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch off.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.
  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


2.CHECK CONNECTORS
  1. Disconnect the connector from the center airbag sensor assembly.

  1. Disconnect the connector from the front seat inner belt assembly LH.

  1. Check that the connectors (on the center airbag sensor assembly side and front seat inner belt assembly LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.

    Condition
    Proceed to
    Normal (separate seat)
    A
    Normal (bench seat)
    B
    Abnormal
    C



B
Go to step 5

C
REPLACE HARNESS OR CONNECTOR
A


3.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

C172903E04

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F20-1 (LBE-) - Body ground
    Ignition switch ON
    Below 1 V
    F20-2 (LBE+) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F20-1 (LBE-) - F20-2 (LBE+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F20-1 (LBE-) - F20-2 (LBE+)
    Always
    1 MΩ or Higher
    F20-1 (LBE-) - Body ground
    Always
    1 MΩ or Higher
    F20-2 (LBE+) - Body ground
    Always
    1 MΩ or Higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    H100892E05
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

HINT:
DTCs other than B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 8
OK

REPLACE USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

C190121E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F23-1 (LBE-) - Body ground
    Ignition switch ON
    Below 1 V
    F23-2 (LBE+) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F23-1 (LBE-) - F23-2 (LBE+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F23-1 (LBE-) - F23-2 (LBE+)
    Always
    1 MΩ or Higher
    F23-1 (LBE-) - Body ground
    Always
    1 MΩ or Higher
    F23-2 (LBE+) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 7
OK


6.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    C190122E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

HINT:
DTCs other than B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 8
OK

REPLACE USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

C162326E03

  1. Disconnect the No. 2 floor wire connector from the No. 1 seat wire.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    BK1-1 (DBE-) - Body ground
    Ignition switch ON
    Below 1 V
    BK1-2 (DBE+) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-1 (DBE-) - BK1-2 (DBE+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-1 (DBE-) - BK1-2 (DBE+)
    Always
    1 MΩ or Higher
    BK1-1 (DBE-) - Body ground
    Always
    1 MΩ or Higher
    BK1-2 (DBE+) - Body ground
    Always
    1 MΩ or Higher



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE NO. 1 SEAT WIRE 

8.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly for Bench Seat Type (Click here) or for Separate Seat Type (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


9.CHECK CENTER AIRBAG SENSOR ASSEMBLY
C190123E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

HINT:
DTCs other than B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END