DTC B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction |
| DTC No. | DTC Detections Conditions | Trouble Areas |
| B1660/43 |
|
|

| 1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION |
Turn the ignition switch to the ON position.
Check the passenger airbag ON/OFF indicator operation.

| ON/OFF Indicator Illumination | Proceed to |
| Always ON | A |
| OFF | B |
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the hazard warning signal switch assembly.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and passenger seat belt warning light assembly side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK HAZARD WARNING SIGNAL SWITCH ASSEMBLY (PASSENGER AIRBAG ON/OFF INDICATOR) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Check the passenger airbag ON/OFF indicator operation.
|
| ||||
| NG | |
| 5.CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the passenger seat belt warning light assembly.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-17 (P-AB) - Body ground | Always | 1 MΩ or Higher |
| A21-23 (PAON) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 6.CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-17 (P-AB) - A21-23 (PAON) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 7.CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() |
Using a service wire, connect H7-5 (SW-) and H7-12 (AIR) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-23 (PAON) - A21-17 (P-AB) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() |
Disconnect the service wire from connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21-23 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| A21-17 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 9.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the hazard warning signal switch assembly.
|
| ||||
| OK | |
| 10.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and passenger seat belt warning light assembly side) are not damaged (Click here).
|
| ||||
| OK | |
| 11.CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() |
Disconnect the connector from the passenger seat belt warning light assembly.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-17 (P-AB) - Body ground | Always | 1 MΩ or Higher |
| A21-23 (PAON) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 12.CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-17 (P-AB) - A21-23 (PAON) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 13.CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() |
Using a service wire, connect H7-5 (SW-) and H7-12 (AIR) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-23 (PAON) - A21-17 (P-AB) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 14.CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() |
Disconnect the service wire from connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21-23 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| A21-17 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 15.CHECK WIRE HARNESS (POWER SOURCE) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| H7-3 (IG+) - Body ground | Ignition switch ON | 10 to 14 V |
|
| ||||
| OK | |
| 16.CHECK HAZARD WARNING SIGNAL SWITCH ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connector to the hazard warning signal switch.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Using a service wire, connect H7-5 (SW-) and H7-7 (E) of hazard warning signal switch assembly connector.
Using a service wire, connect H7-12 (AIR) and H7-7 (E) of hazard warning signal switch assembly connector.
Turn the ignition switch to the ON position.
Check the passenger airbag ON/OFF indicator operation.
|
| ||||
| OK | |
| 17.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the center airbag sensor assembly.
Connect the connector to the passenger seat belt warning light assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||