Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1630/23    Driver Side Rear Airbag Sensor Circuit Malfunction

DTC    B1635/24    Front Passenger Side Rear Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The airbag sensor LH consists of parts such as the safing sensor, the diagnostic circuit and the lateral deceleration sensor. The configuration of the rear airbag sensor RH is the same as that of the LH.
When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1630/23 is set when a malfunction is detected in the curtain shield airbag sensor (driver seat side) circuit.
DTC B1635/24 is set when a malfunction is detected in the curtain shield airbag sensor (front passenger seat side) circuit.

DTC No.
DTC Detections Conditions
Trouble Areas
B1630/23
  1. The center airbag sensor assembly receives an open circuit signal in the curtain shield airbag sensor (Driver seat side) circuit for 2 seconds
  2. Rear airbag sensor LH malfunction
  3. Side airbag sensor assembly LH malfunction
  4. Center airbag sensor assembly center malfunction
  1. Rear airbag sensor LH
  2. Side airbag sensor assembly LH
  3. Center airbag sensor assembly
  4. No. 2 floor wire
B1635/24
  1. The center airbag sensor assembly receives an open circuit signal in the curtain shield airbag sensor (Front passenger seat side) circuit for 2 seconds
  2. Rear airbag sensor RH malfunction
  3. Side airbag sensor assembly RH malfunction
  4. Center airbag sensor assembly center malfunction
  1. Rear airbag sensor RH
  2. Side airbag sensor assembly RH
  3. Center airbag sensor assembly
  4. Floor wire

HINT:
Troubleshoot DTC B1620/21 first when the DTC B1620/21 and B1630/23 are output simultaneously.


WIRING DIAGRAM


H101817E03


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. Check the DTC (Click here).

      Result:
      Result
      Proceed to
      DTC B1630/23 is output.
      A
      DTC B1635/24 is output.
      B
      DTC B1630/23 and B1635/24 are output.
      C
      Neither DTC B1630/23 nor B1635/24 is output.
      D



B
Go to step 12

C
Go to step 22

D
USE SIMULATION METHOD TO CHECK
A


2.CHECK CONNECTOR OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor assembly LH and the rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).

OK:
The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK NO. 2 FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E01
  1. Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.

  1. Using SST, connect S13-2 (BCL+) and S13-1 (BCL-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK NO. 2 FLOOR WIRE (FOR SHORT)


    H101480E01
  1. Disconnect the SST from connector C.

  1. Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


6.CHECK NO. 2 FLOOR WIRE (TO B+)


    H101480E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    S11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


7.CHECK NO. 2 FLOOR WIRE (TO GROUND)


    H101480E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Always
    1 MΩ or Higher
    S11-2 (BCL-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


8.CHECK REAR AIRBAG SENSOR LH


    H100203E01
  1. Connect the connector to the side airbag sensor assembly LH.

  1. Interchange the rear airbag sensor LH with the rear airbag sensor RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1630/23 is output.
    A
    DTC B1635/24 is output.
    B
    Neither DTC B1630/23 nor B1635/24 is output.
    C



B
REPLACE REAR AIRBAG SENSOR LH

C
USE SIMULATION METHOD TO CHECK
A


9.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    H100203E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.

  1. Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1630/23 is output.
    A
    DTC B1635/24 is output.
    B
    Neither DTC B1630/23 nor B1635/24 is output.
    C

HINT:
DTCs other than B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C
USE SIMULATION METHOD TO CHECK
A


10.REPLACE CENTER AIRBAG SENSOR ASSEMBLY


    H100180E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1630/23 is not output.

HINT:
DTCs other than B1630/23 may be output at this time, but they are not related to this check.



OK
END
NG


11.CHECK REAR AIRBAG SENSOR LH


    H101845E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the rear airbag sensor LH for Double Cab (Click here) or for Access Cab (Click here).

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1630/23 is not output.

HINT:
DTCs other than B1630/23 may be output at this time, but they are not related to this check.



NG
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH
OK

END 

12.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor assembly RH and the rear airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


13.CHECK CONNECTORS
  1. Check that the connectors (on the side airbag sensor assembly RH side and airbag sensor rear RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


14.CHECK FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E03
  1. Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.

  1. Using SST, connect S14-2 (BCR+) and S14-1 (BCR-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


15.CHECK FLOOR WIRE (FOR SHORT)


    H101480E02
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


16.CHECK FLOOR WIRE (TO B+)


    H101480E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    S12-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


17.CHECK FLOOR WIRE (TO GROUND)


    H101480E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Always
    1 MΩ or Higher
    S12-2 (BCR-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


18.CHECK REAR AIRBAG SENSOR RH


    H100203E02
  1. Connect the connector to the side airbag sensor assembly RH.

  1. Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1635/24 is output.
    A
    DTC B1630/23 is output.
    B
    Neither DTC B1630/23 nor B1635/24 is output.
    C



B
REPLACE REAR AIRBAG SENSOR RH

C
USE SIMULATION METHOD TO CHECK
A


19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    H100203E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.

  1. Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1635/24 is output.
    A
    DTC B1630/23 is output.
    B
    Neither DTC B1630/23 nor B1635/24 is output.
    C



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C
USE SIMULATION METHOD TO CHECK
A


20.REPLACE CENTER AIRBAG SENSOR ASSEMBLY


    H101848E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

HINT:
DTCs other than B1635/24 may be output at this time, but they are not related to this check.



OK
END
NG


21.REPLACE REAR AIRBAG SENSOR RH


    H101846E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the rear airbag sensor RH for Double Cab (Click here) or for Access Cab (Click here).

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

HINT:
DTCs other than B1635/24 may be output at this time, but they are not related to this check.



NG
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH
OK

END 

22.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor assembly LH and the rear airbag sensor LH.

  1. Check that the connectors are properly connected to the side airbag sensor assembly RH and the rear airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


23.CHECK CONNECTORS
  1. Check that the connectors (on the side airbag sensor assembly LH side and airbag sensor rear LH side) are not damaged (Click here).

  1. Check that the connectors (on the side airbag sensor assembly RH side and airbag sensor rear RH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


24.CHECK NO. 2 FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E01
  1. Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.

  1. Using SST, connect S13-2 (BCL+) and S13-1 (BCL-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


25.CHECK NO. 2 FLOOR WIRE (FOR SHORT)


    H101480E01
  1. Disconnect the SST from connector C.

  1. Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - S11-2 (BCL-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


26.CHECK NO. 2 FLOOR WIRE (TO B+)


    H101480E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    S11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


27.CHECK NO. 2 FLOOR WIRE (TO GROUND)


    H101480E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (BCL+) - Body ground
    Always
    1 MΩ or Higher
    S11-2 (BCL-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


28.CHECK FLOOR WIRE (FOR OPEN)
SST
09843-18040  


    H101479E03
  1. Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.

  1. Using SST, connect S14-2 (BCR+) and S14-1 (BCR-) of connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


29.CHECK FLOOR WIRE (FOR SHORT)


    H101480E02
  1. Disconnect the SST from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - S12-2 (BCR-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


30.CHECK FLOOR WIRE (TO B+)


    H101480E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    S12-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


31.CHECK FLOOR WIRE (TO GROUND)


    H101480E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 (BCR+) - Body ground
    Always
    1 MΩ or Higher
    S12-2 (BCR-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


32.REPLACE CENTER AIRBAG SENSOR ASSEMBLY


    H101847E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1630/23 and B1635/24 are not output.

HINT:
DTCs other than B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



OK
END
NG


33.REPLACE REAR AIRBAG SENSOR RH


    H101847E01
  1. Connect the connectors to the side airbag sensor assembly RH, the side airbag sensor assembly LH and center airbag sensor assembly.

  1. Replace the rear airbag sensor RH and the rear airbag sensor LH for Double Cab (Click here) or for Access Cab (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1630/23 and B1635/24 are not output.



NG
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH AND SIDE AIRBAG SENSOR ASSEMBLY RH
OK

END