Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch/
    OFF or ON
    1. OFF: Shift lever not in P and N
    2. ON: Shift lever in P or N
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Transfer L4
    Transfer status/
    OFF or ON
    1. OFF: Transfer position is not L4
    2. ON: Transfer position is in L4
    -
    Stop Light Switch
    Stop light switch status/
    OFF or ON
    1. OFF: Brake pedal is released
    2. ON: Brake pedal is depressed
    -
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Input turbine speed (NT) is equal to engine speed: Lock-up is ON (after warming up engine)
    2. Input turbine speed (NT) is nearly equal to engine speed: Lock-up is OFF (idling with shift lever in N)
    Data is displayed in increments of 50 rpm.
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    0 km/h (0 mph) (output shaft speed is equal to vehicle speed): Vehicle stopped
    -
    Shift SW Status (P Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in P
    2. ON: Shift lever in P
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (R Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in R
    2. ON: Shift lever in R
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (2 Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in 2
    2. ON: Shift lever in 2
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (L Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in L
    2. ON: Shift lever in L
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (N Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in N
    2. ON: Shift lever in N
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (D Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in D
    2. ON: Shift lever in D
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (4 Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in D and 4
    2. ON: Shift lever in D or 4
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (3 Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in 3
    2. ON: Shift lever in 3
    When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. Approximately 80°C (176°F): After stall test
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or short circuited.
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. Approximately 80°C (176°F): After stall test
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or short circuited
    Lock Up
    Lock up/
    OFF or ON
    1. OFF: Lock-up is not operating
    2. ON: Lock-up is operating
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th or 5th
    Actual gear position
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    OFF or ON
    1. OFF: Accelerator pedal is depressed
    2. ON: Accelerator pedal is released
    -
    SLU Solenoid Status
    Shift solenoid SLU status/
    OFF or ON
    1. OFF: Shift solenoid SLU is not operating
    2. ON: Shift solenoid SLU is operating
    -
    AT Fluid
    Lockup judder judgment/
    OFF or ON
    1. OFF: Judder judgment does not occur
    2. ON: Judder judgment occurs
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLU)
    Operate the shift solenoid SLU
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    OFF or ON

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Solenoid (S1)
    Operate the shift solenoid S1
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (S2)
    Operate the shift solenoid S2
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Lock Up
    Control shift solenoid SLU to set automatic transmission to lock-up condition
    OFF or ON
    Possible to check shift solenoid valve SLU operation
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (37 mph) or more
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (31 mph) or less
    Activate the Solenoid (SR)
    Operate the shift solenoid SR
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL1)
    Operate the shift solenoid SL1
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL2)
    Operate the shift solenoid SL2
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N

HINT:
  1. *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well.
  2. Please note that the pressure values in the Active Test and Hydraulic Test are different from each other.