DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | When one of following conditions is met: |
|
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic).
| ||
(B) All of the following conditions are met simultaneously (2-trip detection logic).
| ||
(C) When any of following conditions is met, the 4 or L position signal is ON for 2.0 seconds or more (2-trip detection logic).
|
| Related DTCs | P0705: Park/neutral position switch/Verify switch input |
| Required sensors/Components | Park/neutral position switch |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (C) 2 seconds Condition (B) 60 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | None |
| Ignition switch | ON |
| Battery voltage | 10.5 V or more |
| One of the following conditions is met; P switch N switch NSW switch | ON |
| R switch | ON |
| D switch | ON |
| 3 switch | ON |
| 2 switch | ON |
| P switch | OFF |
| N switch | OFF |
| NSW switch | OFF |
| R switch | OFF |
| D switch | OFF |
| 3 switch | OFF |
| 2 switch | OFF |
| P switch | ON |
| N switch | ON |
| NSW switch | ON |
| R switch | ON |
| 3 switch | ON |
| Park/neutral position switch | The park/neutral position switch sends only one signal to the ECM. |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch/ OFF or ON |
| When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | PNP switch status/ OFF or ON |
| |
| Shift SW Status (R Range) | PNP switch status/ OFF or ON |
| |
| Shift SW Status (2 Range) | PNP switch status/ OFF or ON |
| |
| Shift SW Status (L Range) | PNP switch status/ OFF or ON |
| |
| Shift SW Status (N Range) | PNP switch status/ OFF or ON |
| |
| Shift SW Status (D Range) | PNP switch status/ OFF or ON |
| |
| Shift SW Status (4 or D) | PNP switch status/ OFF or ON |
| |
| Shift SW Status (3 Range) | PNP switch status/ OFF or ON |
|
| 1.CHECK HARNESS AND CONNECTOR (IG1 FUSE - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the connector from the park/neutral position switch.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P1-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P1-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 4 (B) - 5 (L) | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P and N | 10 kΩ or higher | |
| 2 (RB) - 6 (PL) | Shift lever P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 2 (RB) - 1 (RL) | Shift lever R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 2 (RB) - 9 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 2 (RB) - 7 (DL) | Shift lever in D or 4 | Below 1 Ω |
| Shift lever not in D and 4 | 10 kΩ or higher | |
| 2 (RB) - 3 (2L) | Shift lever in 3 | Below 1 Ω |
| Shift lever not in 3 | 10 kΩ or higher | |
| 2 (RB) - 8 (LL) | Shift lever in 2 or L | Below 1 Ω |
| Shift lever not in 2 and L | 10 kΩ or higher |
| *a | Component without harness connected (Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 4.INSPECT SHIFT LOCK CONTROL ECU (TRANSMISSION CONTROL SWITCH) |
![]() |
Connect the park/neutral position switch connector.
Disconnect the connector from the shift lock control ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 9 (NSSD) - 2 (ATD) | Shift lever in D | Below 1 Ω |
| Shift lever in 4 | 10 kΩ or higher | |
| 9 (NSSD) - 3 (AT4) | Shift lever in D | 10 kΩ or higher |
| Shift lever in 4 | Below 1 Ω | |
| 10 (NSSL) - 5 (AT2) | Shift lever in 2 | Below 1 Ω |
| Shift lever in L | 10 kΩ or higher | |
| 10 (NSSL) - 4 (ATL) | Shift lever in 2 | 10 kΩ or higher |
| Shift lever in L | Below 1 Ω |
| *a | Component without harness connected (Shift lock control ECU (Transmission control switch)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S7-9 (NSSD) - Body ground |
| 11 to 14 V |
| Below 1 V | |
| S7-10 (NSSL) - Body ground |
| 11 to 14 V |
| Below 1 V |
| *a | Front view of wire harness connector (to Shift lock control ECU (Transmission control switch)) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Connect the shift lock control ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E9-35 (P) - E11-12 (E1) |
| 11 to 14 V |
| Below 1 V | |
| E9-28 (R) - E11-12 (E1) |
| 11 to 14 V* |
| Below 1 V | |
| E9-29 (N) - E11-12 (E1) |
| 11 to 14 V |
| Below 1 V | |
| E9-27 (D) - E11-12 (E1) |
| 11 to 14 V |
| Below 1 V | |
| E14-24 (4) - E11-12 (E1) |
| 11 to 14 V |
| Below 1 V | |
| E9-23 (3) - E11-12 (E1) |
| 11 to 14 V |
| Below 1 V | |
| E9-24 (2) - E11-12 (E1) |
| 11 to 14 V |
| Below 1 V | |
| E14-23 (L) - E11-12 (E1) |
| 11 to 14 V |
| Below 1 V |
| *a | Component with harness connected (ECM) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the connector from the ECM.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E10-2 (NSW) - P1-4 (B) | Always | Below 1 Ω |
| P1-4 (B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||