DTC P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2757 | Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range. (2-trip detection logic) |
|
| Related DTCs | P2757: Shift solenoid valve SLU/OFF malfunction Shift solenoid valve SLU/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLU, Valve body, Vehicle speed sensor, Speed sensor (NT), Speed sensor (NO), Throttle position sensor |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) 2 seconds OFF malfunction (B) 0.4 seconds ON malfunction 1.8 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0751, P0973, P0974 (Shift solenoid valve S1 circuit) P0756, P0976, P0977 (Shift solenoid valve S2 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P2759 (Torque converter clutch pressure control solenoid circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) P0776 (Shift solenoid valve SL2 circuit) P0781 (1-2 shift valve circuit) |
| ETCS (Electric throttle control system) | Not system down |
| Transmission range | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0° CA or more |
| Engine | Starting |
| ECM selected gear | 2nd, 3rd, 4th or 5th |
| Vehicle speed | 25 km/h (15.5 mph) or more |
| Transfer neutral position switch | OFF |
| Transfer range | "High" |
| ECM lock-up command | ON (SLU pressure: 513 kPa (5.2 kgf/cm2, 74 psi) or more) |
| Vehicle speed | Less than 120 km/h (74.6 mph) |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 6.5% or more at 2000 rpm (Varies with engine speed) |
| ECM lock-up command | OFF (SLU pressure: less than 4 kPa (0.04 kgf/cm2, 0.6 psi)) |
| Throttle valve opening angle | 7% or more |
| Vehicle speed | Less than 120 km/h (74.6 mph) at 4th gear (Varies with ECM selected gear) |
| Engine speed - Turbine speed (NE - NT) | 70 rpm or more |
| Turbine speed/Output speed (NT/NO) | Less than 3.30, or more than 7.50 |
| Engine speed - Turbine speed (NE - NT) | Less than 35 rpm |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Lock Up | Control shift solenoid SLU to set automatic transmission to lock-up condition | OFF or ON | Possible to check shift solenoid valve SLU operation [Vehicle Condition]
|
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P2757 is output | A |
| P2757 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLU |
![]() |
Remove the shift solenoid valve SLU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (see chapter 2 in the Problem Symptoms Table) |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER ASSEMBLY |
Inspect the torque converter assembly (Click here).
|
| ||||
| OK | ||
| ||