Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0748    Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)

for Preparation Click here


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves S1, S2, SR, SL1 and SL2 which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be driven smoothly (Click here).

DTC No.
DTC Detection Condition
Trouble Area
P0748
The ECM checks for an open or short in the shift solenoid valve SL1 circuit (1-trip detection logic)
  1. Output signal duty equals 100%.
    (NOTE: SL1 output signal duty is less than 100% under normal condition.)
  1. Open or short in shift solenoid valve SL1 circuit
  2. Shift solenoid valve SL1
  3. ECM

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The ECM controls the gear-shifts by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Then the ECM performs the fail-safe function and turns the other functioning shift solenoid valves "ON/OFF". (If an open or short circuit is detected, the ECM cuts the current to the circuit.)
If the ECM detects an open or short in the shift solenoid valve SL1 circuit, the ECM determines that there is a malfunction (Click here).

MONITOR STRATEGY


Related DTCs
P0748: Shift solenoid valve SL1/Range check
Required sensors/Components
Shift solenoid valve SL1
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever this DTC is not present.
None
Ignition switch
ON
Starter
OFF

Condition (A) 
Solenoid current cut status
Not cut
Battery voltage
11 V or more
Target current
0.1 A or more

Condition (B) 
Battery voltage
8 V or more

TYPICAL MALFUNCTION THRESHOLDS

When either condition below is met: Condition (A) or (B)

Condition (A) 
Solenoid status from hybrid IC
Fail

Condition (B) 
Hybrid IC status
Fail

COMPONENT OPERATING RANGE


Output signal duty
Less than 100%

WIRING DIAGRAM


C186142E04


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


HINT:
The shift solenoid valve SL1 is turned ON/OFF normally when the shift lever is in D:

Gearshift controlled by ECM
1st
2nd
3rd
4th
5th
Shift solenoid valve SL1
OFF
OFF
OFF
OFF
ON

1.INSPECT TRANSMISSION WIRE (SL1)


    G020667E86
  1. Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12 (SL1+) - 4 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    12 (SL1+) - Body ground
    Always
    10 kΩ or higher
    4 (SL1-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    C189655E03
  1. Connect the transmission wire connector to the transmission.

  1. Disconnect the connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-33 (SL1+) - E11-32 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E11-33 (SL1+) - Body ground
    Always
    10 kΩ or higher
    E11-32 (SL1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

3.INSPECT SHIFT SOLENOID VALVE SL1


    C151311E04
  1. Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SL1
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)