Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

DTC    C1268    Transfer L4 Position Switch Circuit

DTC    C1283    L4 Position Switch

for Preparation Click here


DESCRIPTION

A-TRAC is activated if wheel skid is detected while the transfer is in the L4 position.

DTC Code
DTC Detecting Condition
Trouble Areas
C1268
L4 detection switch signal input to skid control ECU (master cylinder solenoid) does not match L4 detection switch signal output from ECM.
  1. L4 detection switch (No. 2 transfer indicator switch)
  2. L4 detection switch (No. 2 transfer indicator switch) circuit
  3. Skid control ECU (master cylinder solenoid)
C1283
Detected only during test mode
  1. L4 detection switch (No. 2 transfer indicator switch)
  2. L4 detection switch (No. 2 transfer indicator switch) circuit
  3. Skid control ECU (master cylinder solenoid)

WIRING DIAGRAM


C189752E02


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform zero point calibration (Click here).

1.INSPECT SKID CONTROL ECU (EXI TERMINAL VOLTAGE)


    C189701E02
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-27 (EXI) - Body ground
    Transfer in L4
    Below 1.5 V
    S1-27 (EXI) - Body ground
    Transfer in other than above
    8 to 14 V

  1. Turn the ignition switch off.

  1. Reconnect the skid control ECU (master cylinder solenoid) connector.



NG
Go to step 4
OK


2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Check if the test mode DTC (C1283) is detected.
    Result 
    Result
    Proceed to
    Test mode DTC (C1283) not output
    A
    Test mode DTC (C1283) output
    B



B
REPAIR TRANSFER INDICATOR SWITCH CIRCUIT (L4 POSITION)
A


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are recorded.
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

4.INSPECT L4 DETECTION SWITCH (NO. 2 TRANSFER INDICATOR SWITCH)


    C189756E01
  1. Remove the L4 detection switch (No. 2 transfer indicator switch).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Free
    10 kΩ or higher

  1. Reinstall the L4 detection switch (No. 2 transfer indicator switch).



NG
REPLACE NO. 2 TRANSFER INDICATOR SWITCH
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - L4 DETECTION SWITCH (NO. 2 TRANSFER INDICATOR SWITCH)


    C189757E01
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the T3 L4 detection switch (No. 2 transfer indicator switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-27 (EXI) - T3-1
    Always
    Below 1 Ω
    S1-27 (EXI) - Body ground
    Always
    10 kΩ or higher
    T3-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the T3 L4 detection switch (No. 2 transfer indicator switch) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM)


    C189619E01
  1. Disconnect the E13 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-27 (EXI) - E13-16 (L4)
    Always
    Below 1 Ω
    S1-27 (EXI) - Body ground
    Always
    10 kΩ or higher
    E13-16 (L4) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the skid control ECU (master cylinder solenoid) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)