Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0717    Input Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No.
DTC Detection Condition
Trouble Area
P0717
  1. All conditions below are detected for 5 seconds or more
    (1-trip detection logic):
    1. Gear change not being performed
    2. Gear position: 4th or 5th
    3. T/M input shaft rpm: 300 rpm or less
    4. T/M output shaft rpm: 1000 rpm or more
    5. Transmission range switch fail (P0705): Not detected
    6. R input signal is OFF
    7. L input signal is OFF
    8. Shift solenoid valves, park/neutral position switch and vehicle speed sensor are in normal operation
  1. Open or short in speed sensor (NT) circuit
  2. Speed sensor (NT)
  3. ECM
Using an oscilloscope:
Check the waveform between terminals NT+ and NT- of the ECM connector.
C162170E06

Standard:
Refer to the illustration.

Terminal
NT+ - NT-
Tool setting
1 V/DIV., 2 msec./DIV.
Vehicle condition
Engine is idling)

MONITOR DESCRIPTION

This DTC indicates that a pulse signal is not output from the speed sensor (NT) (Turbine (input) speed sensor) or is weak. The NT terminal of the ECM detects the revolving signal from speed sensor (NT) (input RPM). The ECM outputs a gearshift signal comparing the input speed sensor (NT) with the output speed sensor SP2. While the vehicle is operating in 4th or 5th gear in the shift position of D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL, and stores the DTC.
*1: A pulse signal is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (31 mph) or more.

MONITOR STRATEGY


Related DTCs
P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components (Main)
Speed sensor (NT)
Required sensors/Components (Related)
Speed sensor (SP2)
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
P0746, P0748 (Shift solenoid valve SL1)
P0776, P0778 (Shift solenoid valve SL2)
P0751, P0973, P0974 (Shift solenoid valve S1)
P0756, P0976, P0977 (Shift solenoid valve S2)
Shift change
Shift change is completed and before starting next shift change operation
ECM selected gear
4th or 5th
Output shaft rpm
1000 rpm or more
Transmission range switch fail (P0705)
Not detected
R switch
OFF
L switch
OFF
Engine
Running
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Sensor signal rpm
Less than 300 rpm

COMPONENT OPERATING RANGE


Speed sensor signal rpm
300 rpm or more.

WIRING DIAGRAM


C186140E02


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the Techstream, read the Data List.

Engine and ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12,750 rpm
Lock-up is:
  1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
  2. OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
Data is displayed in increments of 50 rpm

HINT:
  1. SPD (NT) is always 0 while driving:
    Open or short in the sensor or circuit.
  2. SPD (NT) is always less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
    Sensor trouble, improper installation, or intermittent connection trouble in the circuit.

1.INSPECT SPEED SENSOR (NT) INSTALLATION


    C159067E10
  1. Check the speed sensor (NT) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR (NT)
OK


2.INSPECT SPEED SENSOR (NT)


    E116970E30
  1. Disconnect the speed sensor (NT) connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω



NG
REPLACE SPEED SENSOR (NT) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NT) - ECM)


    C189655E01
  1. Connect the speed sensor (NT) connector.

  1. Disconnect the connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-3 (NT+) - E11-4 (NT-)
    20°C (68°F)
    560 to 680 Ω
    E11-3 (NT+) - Body ground
    Always
    10 kΩ or higher
    E11-4 (NT-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)