Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0711    Transmission Fluid Temperature Sensor "A" Performance

for Preparation Click here


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input into the ECM.
The ECM applies a voltage to the temperature sensor through ECM terminal THO1. The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance and the voltage decrease as the temperature becomes higher.
The ECM calculates the fluid temperature based on the voltage signal.

DTC No.
DTC Detection Condition
Trouble Area
P0711
Any of the following conditions (A), (B) or (c) is met:
  1. Transmission wire (No. 1 ATF temperature sensor)
  2. ECM
Condition (A):
(a), (b), (c) and (d) are detected: (2-trip detection logic)
  1. (a) After the engine stopped, 5 hours or more elapse before the engine is started.
  2. (b) After normal driving for 10 minutes and 4.9 km (3.0 miles) or more.
  3. (c) Engine coolant and intake air temperature is 15°C (59°F) or more at 12 seconds after engine start.
  4. (d) ATF temperature is less than 20°C (68°F).
Condition (B):
(a), (b), and (c) are detected: (2-trip detection logic)
  1. (a) After normal driving for over 21 minutes and and 40 seconds 9 km (5.6 miles) or more.
  2. (b) Engine coolant and intake air temperature are more than -10°C (14°F) at 12 seconds after engine start.
  3. (c) ATF temperature is less than 20°C (68°F).
Condition (C):
Both (1) and (2) are detected: (2-trip detection logic)
  1. (a) Engine coolant temperature is less than 35°C (95°F) at engine start.
  2. (b) ATF temperature 110°C (230°F) or more.

MONITOR DESCRIPTION

This DTC indicates that there is a problem with the output from the automatic transmission fluid (ATF) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects any open or short malfunctions in the ATF temperature circuit or a fault of the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, and turns on the MIL.

MONITOR STRATEGY


Related DTCs
P0711: ATF temperature sensor/Rationality check
Required sensors/Components
ATF temperature sensor
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ALL 
The monitor will run whenever the following DTCs are not present
P0712, P0713, P2742, P2743 (ATF temperature sensor "A" circuit)
P0128 (ECT (Engine Coolant Temperature) sensor circuit)
P0111, P011B, P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)

Condition (A) 
Time after engine start
10 minutes or more
Driving distance after engine start
4.9 km (3.0 miles) or more
IAT (12 seconds after engine start)
15°C (59°F) or more
ECT (12 seconds after engine start)
15°C (59°F) or more
Soak time
5 hours or more

Condition (B) 
Time after engine start
21 minutes and 40 seconds or more
Driving distance after engine start
9 km (5.6 miles) or more
IAT (12 seconds after engine start)
-10°C (14°F) or more
ECT (12 seconds after engine start)
-10°C (14°F) or more

Condition (C) 
ECT
60°C (140°F) or more
ECT (12 seconds after engine start)
Less than 35°C (95°F)

TYPICAL MALFUNCTION THRESHOLDS


Condition (A) and (B) 
ATF temperature
Less than 20°C (68°F)

Condition (C) 
ATF temperature
110°C (230°F) or more

COMPONENT OPERATING RANGE


ATF temperature
20 to 110°C (68 to 230°F)

WIRING DIAGRAM


C186139E02


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or short circuited

    HINT:
    When DTC P0712 is output and the Techstream reading is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and the Techstream reading is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the Techstream in order to check if a malfunction exists.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit

HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0711 is output
    A
    P0711 and other DTCs are output
    B

    HINT:
    If any codes besides P0711 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION FLUID LEVEL
  1. Check the transmission fluid level (Click here).

    OK:
    Automatic transmission fluid level is correct.



NG
ADD FLUID (Click here)
OK

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) (Click here)