Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Driver Side Seat Belt Warning Light does not Operate

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the combination meter assembly receives signals from the front seat inner belt assembly (driver side). When the seat belt is unfastened, the combination meter assembly flashes the driver seat belt warning light in the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the front driver seat belt warning light.

WIRING DIAGRAM


E231218E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (DRIVER SIDE SEAT BELT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Driver side seat belt warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.

    OK:
    Driver side seat belt warning light condition can be switched by Active Test.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.CONFIRM SEAT TYPE
  1. Confirm the seat type.
    Result 
    Result
    Proceed to
    for Bench Seat Type
    A
    for Separate Seat Type
    B



B
Go to step 5
A


3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
  1. Disconnect the F22 front seat inner belt assembly (driver side) connector.



    I045519E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt fastened
    10 kΩ or higher
    1 - 2
    Seat belt unfastened
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front Seat Inner Belt Assembly (Driver Side))

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - COMBINATION METER ASSEMBLY AND BODY GROUND)
  1. Disconnect the F22 front seat inner belt assembly (driver side) connector.

  1. Disconnect the C9 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F22-2 - C9-10
    Always
    Below 1 Ω
    F22-2 or C9-10 - Body ground
    Always
    10 kΩ or higher
    F22-1 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the combination meter assembly connector.

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
  1. Disconnect the F21 front seat inner belt assembly (driver side) connector.



    I045523E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt fastened
    10 kΩ or higher
    1 - 2
    Seat belt unfastened
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front Seat Inner Belt Assembly (Driver Side))

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - COMBINATION METER ASSEMBLY AND BODY GROUND)
  1. Disconnect the F21 front seat inner belt assembly (driver side) connector.

  1. Disconnect the C9 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F21-2 - C9-10
    Always
    Below 1 Ω
    F21-2 or C9-10 - Body ground
    Always
    10 kΩ or higher
    F21-1 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the combination meter assembly connector.

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)