Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Vacuum Brake Booster)

DTC    C1361    Short in ABS Motor Fail Safe Relay Circuit

DTC    C146C    Open in ABS Motor Relay Circuit

DTC    C146D    Short in ABS Motor Relay Circuit

for Preparation Click here


DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor.
If the voltage supplied to the motor relay (+BM) is below the DTC detection threshold due to low voltage from the battery or alternator, the DTC may be stored.

DTC Code
DTC Detection Condition
Trouble Area
C1361
Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the motor fail safe relay is OFF.
  1. ABS No. 1 fuse
  2. ABS motor fail safe relay circuit
  3. ABS motor fail safe relay (Brake actuator assembly)
C146C
When either of the following is detected:
  1. All of the following conditions continue for 0.12 seconds or more.
    1. The IG1 terminal voltage is between 9.5 and 17.2 V.
    2. While initial check and ABS, BA, TRAC or VSC is operating.
    3. Relay contact is open when the relay is ON.
  2. Both of the following conditions continue for 0.12 seconds.
    1. The IG1 terminal voltage is less than 9.5 V.
    2. Relay contact remains open when the relay is ON.
  1. ABS No. 1 fuse
  2. ABS motor relay circuit
  3. ABS motor relay (Brake actuator assembly)
C146D
When the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
  1. ABS motor relay circuit
  2. ABS motor relay (Brake actuator assembly)

WIRING DIAGRAM


C189931E02


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

HINT:
When C1241 is output together with C1361, C146C and/or C146D inspect and repair the trouble areas indicated by C1241 first (Click here).

1.INSPECT ABS NO. 1 FUSE


    F051653E08
  1. Remove the ABS No. 1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ABS No. 1 fuse
    Always
    Below 1 Ω



NG
REPLACE ABS NO. 1 FUSE
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (ABS MOTOR RELAY)
  1. Install the ABS No. 1 fuse.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Select the Active Test mode on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    ABS motor relay
    Relay ON / OFF
    Operating sound of motor can be heard

  1. Check the operating sound of the ABS motor relay when operating it with the Techstream.
    Result 
    Result
    Proceed to
    The operating sound is not heard
    A
    The operating sound is heard
    B



B
Go to step 5
A


3.INSPECT SKID CONTROL ECU (+BM TERMINAL)


    C168924E23
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-24 (BM) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)
OK


4.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C168924E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-13 (GND2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The ABS motor relay is in the brake actuator assembly.
Therefore, ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Turn the ignition switch off.

  1. Reconnect the skid control ECU (brake actuator assembly) connector.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
    2. If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
    4. It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)