Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION ECU (for Bench Seat Type)

OCCUPANT CLASSIFICATION ECU (for Bench Seat Type) > REMOVAL

for Preparation Click here


NOTICE:
  1. If the wiring connector of the SRS is disconnected with the ignition switch in the ON position, DTCs will be recorded.
  2. Never use SRS parts from another vehicle. When replacing the parts, replace them with new ones.
  1. Never reuse an occupant classification ECU if an airbag has previously deployed in a collision.
  2. Remove the front seat cushion cover pad and front seat cushion cover together, in order to avoid occupant classification sensor malfunctions.



1. READ IN OCCUPANT CLASSIFICATION ECU DATA

NOTICE:
  1. If any DTCs related to the occupant classification ECU are output, troubleshoot those DTCs by referring to the DIAGNOSTIC TROUBLE CODE CHART.
  2. When ECU data saving or loading operations cannot be performed, replace the front seat cushion assembly (with occupant classification ECU and occupant classification sensor).

HINT:
  1. When the occupant classification ECU for a bench seat type is replaced, the previous ECU data must be saved in the Techstream and loaded into the new ECU by following the flowchart below.
  2. Until the data from the previous ECU are loaded into the new occupant classification ECU, these data are not erased even when the Techstream is turned off.
  3. ECU EXCHANGE PROCEDURE (Before Exchange) describes the procedure to save the data in the Techstream from the occupant classification ECU which has been installed on the vehicle. ECU EXCHANGE PROCEDURE (After Exchange) describes the procedure to load the data from the previous ECU, stored in the Techstream, into the new ECU.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Store the occupant classification ECU data into the Techstream by following the prompts on the Techstream screen.

    HINT:
    If the ECU data cannot be stored in the Techstream, replace the front seat cushion assembly (with occupant classification ECU and occupant classification sensor).

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Load the data from the previous ECU stored in the Techstream, into the newly installed ECU by following the prompts on the Techstream screen.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    If DTC is not cleared at this time, past DTC will remain.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag from working.


3. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    B121777
  1. Slide the front seat to the most forward position.

  1. Disengage the hook.

  1. Disconnect the 2 connectors.

  1. Using a clip remover, remove the wiring harness clamp.

  1. Remove the wiring harness clamp.

  1. Remove the bolt and the front seat inner belt.



4. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH


    B121778
  1. Slide the front seat to the most forward position.

  1. Disengage the hook.

  1. Disconnect the connector.

  1. Using a clip remover, remove the wiring harness clamp.

  1. Remove the wiring harness clamp.

  1. Remove the bolt and the front seat inner belt.



5. REMOVE FRONT SEAT HEADREST ASSEMBLY


    B121738E01
  1. Push in the 2 lock buttons of the 2 front seat headrest supports and remove the 2 front seat headrests.



6. REMOVE FRONT SEAT ASSEMBLY


    B121739
  1. Remove the belt of the front center seat outer belt from the front center seat outer belt guide.



    B203884
  1. Disconnect the 5 connectors.

  1. Using a clip remover, remove the 2 wiring harness clamps.



    B121741
  1. Remove the 4 bolts and the front seat.



7. REMOVE OCCUPANT CLASSIFICATION ECU


    C123157
  1. Disconnect the connector from the occupant classification ECU.

  1. Remove the 2 bolts and the occupant classification ECU.