Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0111    Intake Air Temperature Sensor Gradient Too High

for Preparation Click here


DESCRIPTION

A067628E24
  1. The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature sensor. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature sensor is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
  2. The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, the voltage at terminal THA also varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

DTC No.
DTC Detection Condition
Trouble Area
P0111
Either condition below is met (2 trip detection logic):
  1. The intake air temperature change, from the previous trip warm-up to the following trip is small.
  2. The change in the intake air temperature after engine start is less than the threshold value.
Mass air flow meter

MONITOR DESCRIPTION

  1. After warmed engine stop
    The ECM monitors the intake air temperature variation in the period from when the engine was warmed up on the previous trip until the next engine start. If the change in engine coolant temperature sensor output is less than the threshold, it is determined that a malfunction has occurred in the intake air temperature sensor. When this is detected, the MIL is illuminated and the DTC is stored.
  1. After cold engine start
    The monitor runs when the engine is started cold after 5 hours or more have elapsed since the engine stopped. If the intake air temperature sensor output variation until the engine has warmed up completely is less than the threshold, it is determined that a malfunction has occurred in the intake air temperature sensor. When this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.

MONITOR STRATEGY


Related DTCs
P0111: Intake Air Temperature Sensor Rationality (After Engine Stop)
P0111: Intake Air Temperature Sensor Rationality (After Cold Engine Start)
Required Sensors/Components (Main)
Intake air temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
10 seconds or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs are not present
None

After Engine Stop 
Time after engine start
10 seconds or more
Battery voltage
10.5 V or more
Engine coolant temperature at ECM started by soak timer
-40°C (-40°F) or higher
Engine coolant temperature before engine stop
70°C (158°F) or higher
Accumulated mass air flow amount before engine stop
2057 g or more
Key-off duration
30 minutes
Mass air flow meter circuit fail (P0102, P0103)
Not detected
Engine coolant temperature sensor circuit (P0115, P0117, P0118)
Not detected
Intake air temperature circuit fail (P0112, P0113)
Not detected
Soak timer circuit fail (P2610)
Not detected

After Cold Engine Start 
Key-off duration
5 hours
Time after engine start
10 seconds or more
Engine coolant temperature
70°C (158°F) or higher
Accumulated mass air flow amount
2057 g or more
Either of the following conditions 1 or 2 is met:
-
1. Duration while engine load is low
120 seconds or more
2. Duration while engine load is high
10 seconds or more
Mass air flow meter circuit fail (P0102, P0103)
Not detected
Engine coolant temperature sensor circuit (P0115, P0117, P0118)
Not detected
Intake air temperature circuit fail (P0112, P0113)
Not detected
Soak timer circuit fail (P2610)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


After Engine Stop 
Intake air temperature change
Less than 1°C (2°F)

After Cold Engine Start 
Intake air temperature change
Less than 1°C (2°F)

CONFIRMATION DRIVING PATTERN


A198822E16

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].

    HINT:
    During steps [A] through [C], if the change in the intake air temperature is below 1°C (1.8°F), the intake air temperature sensor (mass air flow meter) is malfunctioning. It is not necessary to continue this procedure.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0111.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].

  13. Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Check the DTC judgment result again [F].

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0112 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0111 and other DTCs are output
    A
    P0111 is output
    B

    HINT:
    If any DTCs other than P0111 are output, troubleshoot those DTCs first.



B
REPLACE MASS AIR FLOW METER
A

GO TO DTC CHART (Click here)