Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

The radio receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM


E232746E01


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


2.CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E232747E01
  1. Disconnect the S19 and S20 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-) - 3 (-)
    Always
    Below 1 Ω
    2 (+) - 4 (+)
    Always
    Below 1 Ω
    3 (-) - 4 (+)
    Always
    3.4 to 4.6 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Regular CAB)
    B
    NG (except Regular CAB)
    C



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
  1. Disconnect the R1 radio receiver assembly connector.

  1. Disconnect the S19 and S20 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R1-2 (FL+) - S19-4 (+)
    Always
    Below 1 Ω
    R1-6 (FL-) - S19-3 (-)
    Always
    Below 1 Ω
    R1-1 (FR+) - S20-4 (+)
    Always
    Below 1 Ω
    R1-5 (FR-) - S20-3 (-)
    Always
    Below 1 Ω
    R1-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R1-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    R1-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R1-5 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E232748E01
  1. Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Regular CAB)
    B
    NG (except Regular CAB)
    C



B
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
  1. Disconnect the S19 and S20 front No. 2 speaker assembly connectors.

  1. Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S19-1 (-) - S15-2
    Always
    Below 1 Ω
    S19-2 (+) - S15-1
    Always
    Below 1 Ω
    S20-1 (-) - S16-2
    Always
    Below 1 Ω
    S20-2 (+) - S16-1
    Always
    Below 1 Ω
    S19-1 (-) - Body ground
    Always
    10 kΩ or higher
    S19-2 (+) - Body ground
    Always
    10 kΩ or higher
    S20-1 (-) - Body ground
    Always
    10 kΩ or higher
    S20-2 (+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK REAR SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Rear speaker assembly (for Double Cab)
    A
    No. 1 speaker assembly with box (for 7 Speakers)
    B
    Roof speaker assembly (for Access Cab)
    C



B
Go to step 10

C
Go to step 12
A


8.INSPECT REAR SPEAKER ASSEMBLY


    E232748E01
  1. Disconnect the S17 and S18 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
  1. Disconnect the R2 radio receiver assembly connector.

  1. Disconnect the S17 and S18 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R2-2 (RL+) - S17-1
    Always
    Below 1 Ω
    R2-6 (RL-) - S17-2
    Always
    Below 1 Ω
    R2-1 (RR+) - S18-1
    Always
    Below 1 Ω
    R2-3 (RR-) - S18-2
    Always
    Below 1 Ω
    R2-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R2-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    R2-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R2-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

10.INSPECT NO. 1 SPEAKER ASSEMBLY WITH BOX


    E170614E02
  1. Disconnect the S30 No. 1 speaker assembly with box connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 5
    Always
    Approximately 8.7 kΩ
    1 - 4
    Always
    Approximately 4.0 kΩ

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Speaker Assembly with Box)



NG
REPLACE NO. 1 SPEAKER ASSEMBLY WITH BOX (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 SPEAKER ASSEMBLY WITH BOX)
  1. Disconnect the R2 radio receiver assembly connector.

  1. Disconnect the S30 No. 1 speaker assembly with box connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R2-2 (RL+) - S30-2 (L+)
    Always
    Below 1 Ω
    R2-6 (RL-) - S30-5 (L-)
    Always
    Below 1 Ω
    R2-1 (RR+) - S30-1 (R+)
    Always
    Below 1 Ω
    R2-3 (RR-) - S30-4 (R-)
    Always
    Below 1 Ω
    R2-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R2-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    R2-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R2-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

12.INSPECT ROOF SPEAKER ASSEMBLY


    E170616E02
  1. Disconnect the R12 and R13 roof speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Speaker Assembly)



NG
REPLACE ROOF SPEAKER ASSEMBLY
OK


13.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - RADIO SETTING CONDENSER)
  1. Disconnect the R2 radio receiver assembly connector.

  1. Disconnect the R11 radio setting condenser connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R2-2 (RL+) - R11-2 (LI+)
    Always
    Below 1 Ω
    R2-6 (RL-) - R11-1 (LI-)
    Always
    Below 1 Ω
    R2-1 (RR+) - R11-4 (RI+)
    Always
    Below 1 Ω
    R2-3 (RR-) - R11-3 (RI-)
    Always
    Below 1 Ω
    R2-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R2-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    R2-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R2-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (RADIO SETTING CONDENSER - ROOF SPEAKER ASSEMBLY)
  1. Disconnect the R11 radio setting condenser connector.

  1. Disconnect the R13 and R12 roof speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R11-6 (LO+) - R13-1
    Always
    Below 1 Ω
    R11-5 (LO-) - R13-2
    Always
    Below 1 Ω
    R11-8 (RO+) - R12-1
    Always
    Below 1 Ω
    R11-7 (RO-) - R12-2
    Always
    Below 1 Ω
    R11-6 (LO+) - Body ground
    Always
    10 kΩ or higher
    R11-5 (LO-) - Body ground
    Always
    10 kΩ or higher
    R11-8 (RO+) - Body ground
    Always
    10 kΩ or higher
    R11-7 (RO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.REPLACE RADIO SETTING CONDENSER
  1. Replace the radio setting condenser with a new or normal.

    OK:
    Sound is heard from the roof speakers.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END