Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (w/o Navigation System)

REAR VIEW MONITOR SYSTEM (w/o Navigation System) > Image from Camera for Rear View Monitor is Abnormal


DESCRIPTION

The display signal of the rear television camera assembly is transmitted to the inner rear view mirror assembly.

WIRING DIAGRAM


E236289E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the I8 inner rear view mirror assembly connector.

  1. Disconnect the T19 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I8-14 (CB+) - T19-4 (CB+)
    Always
    Below 1 Ω
    I8-7 (CV+) - T19-2 (CV+)
    Always
    Below 1 Ω
    I8-6 (CV-) - T19-1 (CV-)
    Always
    Below 1 Ω
    I8-13 (CGND) - T19-3 (CGND)
    Always
    Below 1 Ω
    I8-14 (CB+) - Body ground
    Always
    10 kΩ or higher
    I8-7 (CV+) - Body ground
    Always
    10 kΩ or higher
    I8-6 (CV-) - Body ground
    Always
    10 kΩ or higher
    I8-13 (CGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT INNER REAR VIEW MIRROR ASSEMBLY
  1. Reconnect the inner rear view mirror assembly connector.



    E236466E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I8-6 (CV-) - Body ground
    Below 1 Ω
    Below 1 Ω
    I8-13 (CGND) - Body ground
    Below 1 Ω
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I8-14 (CB+) - I8-13 (CGND)
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Component with harness connected
    (Inner Rear View Mirror Assembly)



NG
REPLACE INNER REAR VIEW MIRROR ASSEMBLY (Click here)
OK


3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
  1. Reconnect the rear television camera assembly connector.



    E236467E01
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    I8-7 (CV+) - I8-6 (CV-)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Waveform 1: Ignition switch ON, shift lever in R
    Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in the illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *a
    Component with harness connected
    (Inner Rear View Mirror Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)