Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (w/ Navigation System)

REAR VIEW MONITOR SYSTEM (w/ Navigation System) > Image from Camera for Rear View Monitor is Abnormal


DESCRIPTION

  1. The display signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.

WIRING DIAGRAM


E233338E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the R17 radio and display receiver assembly connector.

  1. Disconnect the T19 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R17-7 (CA+) - T19-4 (CB+)
    Always
    Below 1 Ω
    R17-8 (V+) - T19-2 (CV+)
    Always
    Below 1 Ω
    R17-16 (V-) - T19-1 (CV-)
    Always
    Below 1 Ω
    R17-15 (CGND) - T19-3 (CGND)
    Always
    Below 1 Ω
    R17-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    R17-8 (V+) - Body ground
    Always
    10 kΩ or higher
    R17-16 (V-) - Body ground
    Always
    10 kΩ or higher
    R17-15 (CGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Reconnect the radio and display receiver assembly connector



    E235766E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R17-16 (V-) - Body ground
    Always
    Below 1 Ω
    R17-15 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R17-7 (CA+) - R17-15 (CGND)
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
  1. Reconnect the rear television camera assembly connector.



    E235768E02
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    R17-8 (V+) - R17-16 (V-)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Waveform 1: Ignition switch ON, shift lever in R
    Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in the illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)