Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Skid Control ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Skid Control ECU Communication Stop Mode
  1. "ABS/VSC/TRAC" not displayed on "Bus Check" screen of Techstream
  2. Applies to "Skid Control ECU Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of master cylinder solenoid (skid control ECU)*1
  2. Power source circuit of brake actuator assembly (skid control ECU)*2
  3. Master cylinder solenoid (skid control ECU) branch wire or connector*1
  4. Brake actuator assembly (skid control ECU) branch wire or connector*2
  5. Master cylinder solenoid (skid control ECU)*1
  6. Brake actuator assembly (skid control ECU)*2
  1. *1: for Hydraulic Booster Type
  2. *2: for Vacuum Booster Type

WIRING DIAGRAM


E214873E11


E214873E12


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NEXT


3.SYSTEM CHECK
  1. Check the vehicle specifications.

Result 
Result
Proceed to
for Hydraulic Booster Type
A
for Vacuum Booster Type
B


B
Go to step 6
A


4.CHECK FOR OPEN IN CAN BUS WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU) BRANCH WIRE)


    E223286E02
  1. Turn the ignition switch off.

  1. Disconnect the S1 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-11 (CANH) - S1-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID (SKID CONTROL ECU) - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.



    E223286E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-32 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)  

6.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) BRANCH WIRE)


    E223287E02
  1. Turn the ignition switch off.

  1. Disconnect the S1 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-25 (CANH) - S1-14 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.



    E223287E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-13 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)