DTC B1661/44 Roll Over Cut Off Indicator Malfunction |
| DTC No. | Detection Condition | Trouble Area |
| B1661/44 |
|
|

| 1.CHECK RSCA OFF INDICATOR OPERATION |
![]() |
Turn the ignition switch to ON.
Check the RSCA OFF indicator operation.
| RSCA OFF Indicator Illumination | Proceed to |
| Always ON | A |
| OFF | B |
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the combination meter assembly.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and combination meter assembly side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK COMBINATION METER ASSEMBLY (RSCA OFF INDICATOR) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the RSCA OFF indicator operation.
| RSCA OFF Indicator Illumination | Proceed to |
| ON | A |
| OFF | B |
|
| ||||
| A | |
| 5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - COMBINATION METER) |
![]() |
Disconnect the connector from the combination meter assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A21-20 (RMIL) - Body ground | Ignition Switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-20 (RMIL) - C9-26 (SW) | Always | Below 1 Ω |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-20 (RMIL) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the combination meter assembly.
|
| ||||
| OK | |
| 7.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and combination meter assembly side) are not damaged (Click here).
|
| ||||
| OK | |
| 8.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - COMBINATION METER) |
![]() |
Disconnect the connector from the center airbag sensor assembly.
Disconnect the connector from the combination meter assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A21-20 (RMIL) - Body ground | Ignition Switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-20 (RMIL) - C9-26 (SW) | Always | Below 1 Ω |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-20 (RMIL) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C9-21 (IG+) - Body ground | Ignition Switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 10.CHECK COMBINATION METER ASSEMBLY (RSCA OFF INDICATOR) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.
Connect the connector to the combination meter assembly.
Disconnect the connector from the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Using a service wire, connect C9-26 (SW) and C9-2 (E) of the combination meter assembly connector.
Turn the ignition switch to ON.
Check the RSCA OFF indicator operation.
|
| ||||
| OK | |
| 11.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the center airbag sensor assembly.
Connect the connector to the combination meter assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||