Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

DTC    P0018    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)

for Preparation Click here


DESCRIPTION

Refer to DTC P0335 .

DTC Code
DTC Detection Condition
Trouble Area
P0016
Deviations in crankshaft and camshaft position sensor 1 signals (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. Oil control valve (OCV)
  3. Camshaft timing gear assembly
  4. ECM
P0018
Deviations in crankshaft and camshaft position sensor 2 signals (2 trip detection logic)

MONITOR DESCRIPTION

The ECM optimizes the valve timing by using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the Oil Control Valve (OCV) and the VVT controller.
The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft. The ECM calibrates the intake valve timing by setting the intake camshaft to the most retarded angle while the engine is idling. The ECM closes the OCV to retard the cam. The ECM stores this value as the VVT learning value. When the difference between the target and actual intake valve timings is 5°CA (Crankshaft Angle) or less, the ECM stores it.
If the VVT learning value matches the following conditions, the ECM determines the existence of a malfunction in the VVT system, and sets the DTC.
  1. VVT learning value: Less than 22.5°CA, or more than 45.2°CA.
  2. Above condition continues for 18 seconds or more.
This DTC indicates that the intake camshaft has been installed toward the crankshaft at an incorrect angle, caused by factors such as the timing chain having jumped a tooth.
This monitor begins to run after the engine has idled for 5 minutes.

MONITOR STRATEGY


Related DTCs
P0016: Camshaft Timing Misalignment at idling
Required Sensors/Components (Main)
VVT actuator
Required Sensors/Components (Related)
VVT sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
Less than 1 minute
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0016, P0018 (VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Meter)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
Engine RPM
500 to 1000 rpm

TYPICAL MALFUNCTION THRESHOLDS


One of following conditions is met
-
VVT learning value at maximum retarded valve timing (bank 1)
Less than 22.5 °CA (crankshaft angle)
VVT learning value at maximum retarded valve timing (bank 2)
Less than 22.5 °CA (crankshaft angle)
VVT learning value at maximum retarded valve timing (bank 1)
More than 45.2 °CA (crankshaft angle)
VVT learning value at maximum retarded valve timing (bank 2)
More than 45.2 °CA (crankshaft angle)

WIRING DIAGRAM

Refer to DTC P0335 .
Refer to DTC P0340 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0016, P0018
    A
    P0016, P0018 and other DTCs
    B



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream ON.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.

    OK:

    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Engine idles roughly or stalls
    (soon after OCV switched from OFF to ON)



NG
Go to step 4
OK


3.ADJUST VALVE TIMING


    G036290E11
  1. Remove the cylinder head cover .

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover .



NEXT
Go to step 6

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A148714E08
  1. Remove the OCV (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


5.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).


NEXT


6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. In order to erase the ECM learned values for valve timing, disconnect the cable from the negative (-) battery terminal for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes.

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    DTCs are not output.



NG
GO TO DTC CHART (Click here)
OK

END