Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

DTC    P0017    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

DTC    P0018    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)

DTC    P0019    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

for Preparation Click here


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC Code
DTC Detection Condition
Trouble Area
P0016
Deviation in crankshaft position sensor signal and VVT sensor 1 (for Intake Camshaft Bank 1) signal (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. ECM
P0017
Deviation in crankshaft position sensor signal and VVT sensor 1 (for Exhaust Camshaft Bank 1) signal (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. ECM
P0018
Deviation in crankshaft position sensor signal and VVT sensor 2 (for Intake Camshaft Bank 2) signal (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. ECM
P0019
Deviation in crankshaft position sensor signal and VVT sensor 2 (for Exhaust Camshaft Bank 2) signal (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0016 (Bank 1) or P0018 (Bank 2).
To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0017 (Bank 1) or P0019 (Bank 2).

MONITOR STRATEGY


Related DTCs
P0016: Camshaft timing misalignment at idling (Bank 1 Intake Side)
P0017: Camshaft timing misalignment at idling (Bank 1 Exhaust Side)
P0018: Camshaft timing misalignment at idling (Bank 2 Intake Side)
P0019: Camshaft timing misalignment at idling (Bank 2 Exhaust Side)
Required Sensors/Components (Main)
VVT actuator
Required Sensors/Components (Related)
Camshaft position sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
Within 1 minute
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0016 and P0018 
Monitor runs whenever following DTCs not present
P0010, P0020,(VVT Oil control valve)
P0016, P0018 (VVT System)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P1340 (Camshaft position sensor)
VVT feedback mode
Executing
VVT
Maximum advanced or retarded position
Engine RPM
400 to 1400 rpm

P0017 and P0019 
Monitor runs whenever following DTCs not present
P0013, P0023 (Exhaust VVT Oil control valve)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P1340 (Camshaft position sensor)
VVT feedback mode
Executing
VVT
Maximum advanced or retarded position
Engine RPM
400 to 1400 rpm

TYPICAL MALFUNCTION THRESHOLDS


Intake side: 
One of following conditions met
-
VVT learning value when camshaft maximum retarded
Less than 22.23°CA
VVT learning value when camshaft maximum retarded
More than 46.68°CA

Exhaust side: 
One of following conditions met
-
VVT learning value when camshaft maximum retarded
Less than 82.23°CA
VVT learning value when camshaft maximum retarded
More than 106.68°CA

WIRING DIAGRAM

Refer to DTC P0335 .
Refer to DTC P0340 .
Refer to DTC P0365 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0016, P0017, P0018 or P0019 is output
    A
    P0016, P0017, P0018 or P0019 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream ON.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) or Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Varies



NG
Go to step 4
OK


3.ADJUST VALVE TIMING
  1. Adjust the valve timing (Click here).



NEXT
Go to step 6

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE
A160397E02
A097066E17
  1. Remove the OCV (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. Apply positive (+) battery voltage to terminal 1 and negative (-) battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE (Click here)
OK


5.REPLACE CAMSHAFT TIMING GEAR
  1. Replace the camshaft timing gear (Click here).


NEXT


6.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Clear the DTC (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Read DTCs using the Techstream.

    OK:
    No DTC is output.



NG
GO TO DTC CHART (Click here)
OK

END