DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) |
DTC P0020 Camshaft Position "A" Actuator Circuit (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0010 | Open or short in OCV for intake camshaft (for Bank 1) circuit (1 trip detection logic) |
|
| P0020 | Open or short in OCV for intake camshaft (for Bank 2) circuit (1 trip detection logic) |
|
| Related DTCs | P0010: VVT OCV range check (Bank 1) P0020: VVT OCV range check (Bank 2) |
| Required Sensors/Components (Main) | VVT OCV |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| All of following conditions met | - |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 0.5 seconds or more |
| One of following conditions met | - |
| A. All of following conditions met | - |
| Battery voltage | 11 to 13 V |
| Target duty ratio | Less than 70% |
| Output signal duty ratio | 100% |
| B. All of following conditions met | - |
| Battery voltage | 13 V or more |
| Target duty ratio | Less than 80% |
| Output signal duty ratio | 100% |
| C. Both of following conditions met | - |
| Current cut status | Not cut |
| Output signal duty ratio | 3% or less |
| VVT OCV duty ratio | 3 to 100% |

| 1.CHECK DTC |
Clear DTC after recording the freeze frame data and DTC (Click here).
Turn the ignition switch off.
Allow the engine to idle and check DTC.
Check that P0010 or P0020 is not present.
|
| ||||
| OK | ||
| ||
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Disconnect the D75 or D76 OCV connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (OCV - ECM) |
![]() |
Disconnect the D75 or D76 OCV connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D75-1 - D74-58 (OC1+) | Always | Below 1 Ω |
| D76-1 - D74-52 (OC2+) | Always | Below 1 Ω |
| D75-2 - D74-57 (OC1-) | Always | Below 1 Ω |
| D76-2 - D74-51 (OC2-) | Always | Below 1 Ω |
| D75-1 or D74-58 (OC1+) - Body ground | Always | 10 kΩ or higher |
| D76-1 or D74-52 (OC2+) - Body ground | Always | 10 kΩ or higher |
| D75-2 or D74-57 (OC1-) - Body ground | Always | 10 kΩ or higher |
| D76-2 or D74-51 (OC2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||