DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2123 | VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b) VPA between 0.4 V and 3.45 V |
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 0.02 V or less (b) VPA 0.4 V or less and VPA2 1.2 V or less |
|
| Trouble Area | Accel Sensor Out No. 1 When AP Released | Accel Sensor Out No. 2 When AP Released | Accel Sensor Out No. 1 When AP Depressed | Accel Sensor Out No. 2 When AP Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.7 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.7 V |
| Related DTCs | P2120: APP sensor 1 range check (fluctuating) P2122: APP sensor 1 range check (low voltage) P2123: APP sensor 1 range check (high voltage) P2125: APP sensor 2 range check (fluctuating) P2127: APP sensor 2 range check (low voltage) P2128: APP sensor 2 range check (high voltage) P2138: APP sensor range check (correlation) |
| Required Sensors/Components (Main) | APP sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P2120, P2122, P2125 and P2127 2.0 seconds: P2123, P2128 and P2138 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Either of following conditions 1 or 2 met: | - |
| 1. Ignition switch | ON |
| 2. Throttle actuator power | ON |
| Either of following conditions 1 or 2 met: | - |
| 1. VPA voltage when VPA2 voltage 0.04 V or more | 0.4 V or less |
| 2. VPA voltage | 4.8 V or more |
| VPA voltage when VPA2 voltage 0.04 V or more | 0.4 V or less |
| VPA voltage | 4.8 V or more |
| Either of following conditions 1 or 2 met: | - |
| 1. VPA2 voltage when VPA voltage 0.04 V or more | 1.2 V or less |
| 2. VPA2 voltage when VPA voltage 0.4 to 3.45 V | 4.8 V or more |
| VPA2 voltage when VPA voltage 0.04 V or more | 1.2 V or less |
| VPA2 voltage when VPA voltage 0.4 to 3.45 V | 4.8 V or more |
| Either of following conditions A or B met: | - |
| Condition A | - |
| Difference between VPA and VPA 2 voltages | 0.02 V or less |
| Condition B | - |
| VPA voltage | 0.4 V or less |
| VPA2 voltage | 1.2 V or less |
| VPA voltage | 0.5 to 4.7 V |
| VPA2 voltage | 1.2 to 4.7 V |
| Difference between VPA and VPA2 voltages | More than 0.02 V |

| 1.READ VALUE USING TECHSTREAM (ACCELERATOR POSITION SENSOR) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the value displayed on the Techstream.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
| Released → Depressed → Released | 0.5 to 4.5 V | 1.2 to 4.7 V |
| Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 is higher than 0.02 V | Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 is higher than 0.02 V |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A14 APP sensor connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A14-6 (VPA) - A24-55 (VPA) | Always | Below 1 Ω |
| A14-5 (EPA) - A24-58 (EPA) | Always | Below 1 Ω |
| A14-4 (VCPA) - A24-57 (VCPA) | Always | Below 1 Ω |
| A14-3 (VPA2) - A24-56 (VPA2) | Always | Below 1 Ω |
| A14-2 (EPA2) - A24-60 (EPA2) | Always | Below 1 Ω |
| A14-1 (VCP2) - A24-59 (VCP2) | Always | Below 1 Ω |
| A14-6 (VPA) or A24-55 (VPA) - Body ground | Always | 10 kΩ or higher |
| A14-5 (EPA) or A24-58 (EPA) - Body ground | Always | 10 kΩ or higher |
| A14-4 (VCPA) or A24-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A14-3 (VPA2) or A24-56 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A14-2 (EPA2) or A24-60 (EPA2) - Body ground | Always | 10 kΩ or higher |
| A14-1 (VCP2) or A24-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the A14 APP sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A14-4 (VCPA) - A14-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A14-1 (VCP2) - A14-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ASSEMBLY |
Replace the accelerator pedal assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||