Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here


DESCRIPTION

Refer to DTC P2120 .

DTC Code
DTC Detection Condition
Trouble Area
P2121
Difference between VPA and VPA2 less than 0.4 V, or more than 1.2 V for 0.5 seconds
(1 trip detection logic)
  1. Accelerator Pedal Position (APP) sensor
  1. ECM

MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and the DTC is set.

MONITOR STRATEGY


Related DTCs
P2121: Accelerator pedal position (APP) sensor rationality
Required Sensors/Components (Main)
APP sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Either of following conditions 1 or 2 met:
-
1. Ignition switch
ON
2. Electronic throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


Difference between VPA voltage (learned value) and VPA2 voltage (learned value)
Less than 0.4 V, or more than 1.2 V

FAIL-SAFE

The accelerator pedal position sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned OFF, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. This DTC relates to the Accelerator Pedal Position (APP) sensor.

1.READ VALUE USING TECHSTREAM (ACCELERATOR POSITION SENSOR)
FI07052E06
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

  1. Read the value displayed on the Techstream.

    Standard voltage:
    Accelerator Pedal Operation
    Accel Sensor Out No. 1
    Accel Sensor Out No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



A
Go to step 3
B


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
A115665E20
  1. Disconnect the A14 Accelerator Pedal Position (APP) sensor connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A14-6 (VPA) - A24-55 (VPA)
    Always
    Below 1 Ω
    A14-5 (EPA) - A24-58 (EPA)
    Always
    Below 1 Ω
    A14-4 (VCPA) - A24-57 (VCPA)
    Always
    Below 1 Ω
    A14-3 (VPA2) - A24-56 (VPA2)
    Always
    Below 1 Ω
    A14-2 (EPA2) - A24-60 (EPA2)
    Always
    Below 1 Ω
    A14-1 (VCP2) - A24-59 (VCP2)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A14-6 (VPA) or A24-55 (VPA) - Body ground
    Always
    10 kΩ or higher
    A14-5 (EPA) or A24-58 (EPA) - Body ground
    Always
    10 kΩ or higher
    A14-4 (VCPA) or A24-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A14-3 (VPA2) or A24-56 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A14-2 (EPA2) or A24-60 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A14-1 (VCP2) or A24-59 (VCP2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2121
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)