Home › ENGINE ยท 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here


DESCRIPTION


HINT:
Refer to DTC P2120 .

DTC Code
DTC Detection Condition
Trouble Area
P2121
Difference between VPA and VPA2 less than 0.4 V, or higher than 1.2 V for 0.5 seconds (1 trip detection logic)
  1. Accelerator Pedal Position (APP) sensor
  2. ECM


MONITOR DESCRIPTION

When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the Accelerator Pedal Position (APP) sensor is malfunctioning. The ECM turns on the MIL and the DTC is set.

MONITOR STRATEGY


Related DTCs
P2121: APP sensor rationality
Required Sensors/Components (Main)
APP sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions 1 or 2 met:
-
1. Ignition switch
ON
2. Throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


Difference between VPA voltage (learned value) and VPA2 voltage (learned value)
Less than 0.4 V, or higher than 1.2 V

FAIL-SAFE

The APP sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

HINT:
  1. This DTC relates to the Accelerator Pedal Position (APP) sensor.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2121 is output
    A
    P2121 and other DTCs are output
    B

    HINT:
    If any DTCs other than P2121 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (ACCELERATOR POSITION SENSOR)
FI07052E06
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

  1. Read the values displayed on the Techstream.

    Standard voltage:
    Accelerator Pedal Operations
    Accel Sensor Out No. 1
    Accel Sensor Out No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 4.7 V



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.REPLACE ACCELERATOR PEDAL
  1. Replace the accelerator pedal assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2121 is output
    A
    No DTC is output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)