Home › ENGINE ยท 3UR-FBE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY


    A196289
  1. Attach the 2 clamps to install the No. 6 wire harness to the delivery pipe RH.



    A196288
  1. Attach the 3 clamps to install the No. 7 wire harness to the delivery pipe LH.



    A149190E01
  1. Apply gasoline or spindle oil to a new O-ring and install it to the injector.

    NOTICE:
    Make sure that there is no damage or foreign matter in the groove of the injector when installing the O-ring.



    A161427E01
  1. Connect the injector connector.



    A161479E02
  1. Install the injector to the delivery pipe as shown in the illustration.

    NOTICE:
    1. Make sure that there are no scratches or foreign matter in or around the hole of the delivery pipe.
    2. When installing the injector, be careful not to damage the O-ring.
    3. Attach the part of the injector labeled B between the parts of the delivery pipe labeled A.



    A194618E02
  1. Check that each injector is installed to the delivery pipe facing the direction shown in the illustration.



2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH


    A194617
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head LH.

  1. Install the delivery pipe (with injectors) to the cylinder head LH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    NOTICE:
    A163659E02
    Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.

  1. Connect the No. 7 wire harness connector.

  1. Install the No. 1 engine cover sub-assembly.



3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH


    A194616
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head RH.

  1. Install the delivery pipe (with injectors) to the cylinder head RH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    NOTICE:
    A163659E02
    Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.

  1. Install the No. 3 engine cover.



    A198623
  1. Connect the No. 6 wire harness connector.

  1. Connect the ventilation hose.



4. CONNECT FUEL TUBE SUB-ASSEMBLY


    A161416
  1. Connect the fuel tube to the fuel delivery pipe LH (Click here).



5. CONNECT NO. 1 FUEL TUBE


    A161415
  1. Connect the No. 1 fuel tube to the delivery pipe LH (Click here).



    A161417
  1. Connect the No. 1 fuel tube to the delivery pipe RH (Click here).



6. CONNECT NO. 2 FUEL TUBE


    A161418
  1. Connect the No. 2 fuel tube to the fuel pressure regulator (Click here).



7. INSTALL AIR CLEANER HOSE ASSEMBLY


    A187008
  1. Install the air cleaner hose with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the vacuum hose and ventilation hose.



8. INSTALL V-BANK COVER


    A165576E02
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



10. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to on and Techstream main switch on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.