Home › ENGINE · 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0337    Crankshaft Position Sensor "A" Circuit Low Input

DTC    P0338    Crankshaft Position Sensor "A" Circuit High Input

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position (CKP) sensor system consists of a crankshaft position sensor plate and Magnetic Resistance Element (MRE) type sensor. The crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed to the rear end of the crankshaft. The crankshaft position sensor outputs 34 rotation signals per engine revolution. The ECM uses the G2 signal to distinguish between the cylinders, and uses the NE signal to detect the crankshaft position and engine speed.

DTC No.
DTC Detection Condition
Trouble Area
P0335
  1. No CKP sensor signal to ECM while cranking (1 trip detection logic)
  2. No CKP sensor signal to ECM at engine speed of less than 450 rpm (1 trip detection logic)
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM
P0337
Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM
P0338
Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM
P0339
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or more
(b) Starter signal OFF
(c) 3 seconds or more have elapsed since starter signal switched from ON to OFF
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM

  1. A149739E02
    Reference: Inspection using an oscilloscope.

    Standard:

    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    D74-110 (NE+) - D74-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    D74-90 (G2) - D74-89 (G2-)
    5 V/DIV., 20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown

    HINT:
    G2 stands for the camshaft position sensor signal, and NE stands for the crankshaft position sensor signal.


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.
When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check/rationality
P0337: Crankshaft position sensor check (Low voltage)
P0338: Crankshaft position sensor check (High voltage)
Required sensors/Components (Main)
Crankshaft Position (CKP) sensor
Required sensors/Components (Related)
Camshaft position sensor
Frequency of operation
Continuous
Duration
P0335: 15 seconds
P0337, P0338: 4 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
None

P0335 (Case 1) 
Battery voltage
6 V or higher
CKP sensor voltage
0.3 to 4.7 V
Ignition switch
ON
Starter
ON
Minimum battery voltage while starter ON
Below 11 V

P0335 (Case 2) 
Battery voltage
6 V or higher
CKP sensor voltage
0.3 to 4.7 V
Ignition switch
ON
Engine speed
Less than 450 rpm
Starter
OFF
Time after starter turned from ON to OFF
3 seconds or more

P0337, P0338 
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


P0335: 
Engine speed signal
No signal

P0337: 
CKP sensor voltage
Less than 0.3 V

P0338: 
CKP sensor voltage
More than 4.7 V

COMPONENT OPERATING RANGE


CKP sensor
  1. CKP sensor output voltage fluctuates while engine crankshaft revolving
  2. 34 CKP sensor signals per crankshaft revolution
CKP sensor voltage
0.3 to 4.7 V

WIRING DIAGRAM


A164993E01


INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  2. The engine speed can be checked by using the Techstream. To check, follow the procedures below:
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Turn the Techstream ON.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor output voltage is insufficient.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the Techstream while the engine is running.

    Standard:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the Techstream.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the Techstream remains zero (0), there may be an open or short in the Crankshaft Position (CKP) sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CRANKSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
A107149E60
  1. Disconnect the D3 crankshaft position sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-3 - Body ground
    Ignition switch ON
    4.5 to 5.0 V



NG
Go to step 8
OK


3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A148721E14
  1. Disconnect the D3 crankshaft position sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D3-1 - D74-110 (NE+)
    Always
    Below 1 Ω
    D3-2 - D74-111 (NE-)
    Always
    Below 1 Ω
    D3-1 or D74-110 (NE+) - Body ground
    Always
    10 kΩ or higher
    D3-2 or D74-111 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E25
  1. Check the crankshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE (Click here)
OK


6.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Display (DTC Output)
    Proceed to
    No output
    A
    P0335, P0337, P0338 and/or P0339
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END 

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A148721E15
  1. Disconnect the D3 crankshaft position sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D3-3 - D74-66 (VCV2)
    Always
    Below 1 Ω
    D3-3 or D74-66 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)