Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0748    Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)

for Preparation Click here


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, S1, S2 and SR which are controlled by the ECM. If an open or short circuit occurs in one of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Click here).

DTC Code
DTC Detection Condition
Trouble Area
P0748
  1. ECM detects open or short in shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gear. (1-trip detection logic)
  2. Output signal duty is 100%.

HINT:
SL1 output signal duty is less than 100% under normal condition.

  1. Open or short in shift solenoid valve SL1 circuit
  2. Shift solenoid valve SL1
  3. ECM

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. The ECM performs the fail-safe function and turns the other normal shift solenoid valves "ON/OFF". (In case of an open or short circuit, the ECM stops sending current to the circuit.)
While driving and shifting between 4th and 5th gears, if the ECM detects an open or short in the shift solenoid valve SL1 circuit, the ECM determines there is a malfunction (Click here).

MONITOR STRATEGY


Related DTCs
P0748: Shift solenoid valve SL1/Range check
Required sensors/Components
Shift solenoid valve SL1
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
None
Ignition switch
ON
Starter
OFF

Condition (A) 
Battery voltage
8 V or more

Condition (B) 
Battery voltage
10 V or more and less than 12 V
CPU commanded duty
Less than 75%

TYPICAL MALFUNCTION THRESHOLDS


Output signal duty
100%

COMPONENT OPERATING RANGE


Output signal duty
More than 3% and less than 100%

WIRING DIAGRAM


C161203E01


INSPECTION PROCEDURE


HINT:
The shift solenoid valve SL1 is turned ON/OFF normally when the shift lever is in the D position.

ECM gear shift command
1st
2nd
3rd
4th
5th
Shift solenoid valve SL1
OFF
OFF
OFF
OFF
ON

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL1)


    C159421E02
  1. Disconnect the D63 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    12 (SL1+) - 4 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    12 (SL1+) - Body ground
    Always
    10 kΩ or higher
    4 (SL1-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    C159422E07
  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D74-14 (SL1+) - D74-15 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    D74-14 (SL1+) - Body ground
    Always
    10 kΩ or higher
    D74-15 (SL1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

3.INSPECT SHIFT SOLENOID VALVE SL1
C151311E16
  1. Remove shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal 1 of shift solenoid valve SL1 - terminal 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 1 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE SL1
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)