Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2A00    A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

DTC    P2A03    A/F Sensor Circuit Slow Response (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. DTC P2A00 indicates malfunctions related to the bank 1 A/F sensor.
  2. DTC P2A03 indicates malfunctions related to the bank 2 A/F sensor.
  3. Bank 1 refers to the bank that includes No. 1 cylinder.
  4. Bank 2 refers to the bank that includes No. 2 cylinder.
  5. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC Code
DTC Detection Condition
Trouble Area
P2A00
P2A03
Calculated value for air-fuel ratio (A/F) sensor response rate deterioration level is less than threshold
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor
  3. A/F sensor heater
  4. ECM

MONITOR DESCRIPTION

After engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F control is performed for approximately 10 seconds after preconditions are met in order to measure the A/F sensor response rate. During active A/F control, the ECM forcibly increases and decreases the injection volume a certain amount, based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the A/F sensor response rate. The ECM receives a signal from the A/F sensor while performing active A/F control and uses it to calculate the A/F sensor response rate deterioration level.
If the value for A/F sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and sets the DTC.

A115363E10


CONFIRMATION DRIVING PATTERN


HINT:
Performing this confirmation pattern will activate the A/F sensor response monitor.

A115372E45

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Turn the ignition switch ON.
  3. (c) Turn the Techstream ON.
  4. (d) Clear DTCs (Click here).
  5. (e) Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details.
  6. (f) Check that RES RATE B1S1 and RES RATE B2S1 are Incomplete.
  7. (g) Start the engine and warm it up.
  8. (h) Drive the vehicle at between 25 mph and 75 mph (40 km/h and 120 km/h) for 3 minutes. However, the vehicle should be driven at a constant speed.
  9. (i) Check the monitor result values on Techstream by entering the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / RES RATE B1S1 or RES RATE B2S1 / Details.
  10. (j) If the values indicated on the Techstream do not change, perform READINESS MONITOR DRIVE PATTERN for the A/F sensor and the heated oxygen sensor (Click here).

    HINT:
    Completion of all A/F sensor monitors is required to change the value in RES RATE B1S1 and RES RATE B2S1.

  11. (k) Note the value of the RES RATE B1S1 and RES RATE B2S1.
  12. (l) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
  13. (m) Check if any DTCs (any pending DTCs) are set.

MONITOR STRATEGY


Related DTCs
P2A00: A/F sensor (bank 1) slow response
P2A03: A/F sensor (bank 2) slow response
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
10 to 15 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0110, P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0327, P0328, P0332, P0333 (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2246, P2247 (Secondary Air Injection System)
P0500 (Vehicle Speed Sensor)
P0550 (IAC valve)
Active A/F control
Performing
Active A/F control performed when following conditions met
-
Battery voltage
11 V or more
Engine coolant temperature
75°C (167°F) or more
Idling
OFF
Engine RPM
Less than 4000 rpm
A/F sensor status
Activated
Fuel-cut
OFF
Engine load
10 to 80%
Shift position
2 or more
Catalyst monitor
Not yet
Intake air amount
3 to 20 g/sec.

TYPICAL MALFUNCTION THRESHOLDS


Response rate deterioration level
Less than 0.2 V

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the Techstream.
  1. Connect the Techstream to the DLC3.
  2. Start the engine and turn the Techstream ON.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E05
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E05
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

HINT:
  1. DTC P2A00 or P2A03 may be also set, when the air-fuel ratio is stuck rich or lean.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2A00 and/or P2A03
    A
    P2A00 and/or P2A03 and other DTCs
    B

    HINT:
    If any DTCs other than P2A00 or P2A03 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E04
  1. Disconnect the D33*1 or D34*2 A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (for Bank 1 sensor 1):
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher

    Standard resistance (for Bank 2 sensor 1):
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E03
  1. Disconnect the D33*1 or D34*2 A/F sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D33-1 (HA1A) - D74-22 (HA1A)
    Always
    Below 1 Ω
    D34-1 (HA2A) - D74-20 (HA2A)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D33-1 (HA1A) or D74-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D34-1 (HA2A) or D74-20 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2A00 and/or P2A03
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


6.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


7.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2A00 and/or P2A03
    B



B
CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (REFER TO DTC P0171 PROCEDURE) (Click here)
A

END