Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

HINT:
for Double Cab, CrewMax

  1. If the rear RH side manual UP/DOWN function does not operate, there may be a malfunction in the rear power window regulator switch RH, rear power window regulator motor RH, power window regulator master switch or Harness and connector.

WIRING DIAGRAM


B173121E05


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - BATTERY)
B149730E13
  1. Disconnect the O5 switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O5-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
B166141E03
  1. Remove the switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (U) - 3 (B)
    UP
    Below 1 Ω
    1 (D) - 2 (SD)
    4 (U) - 5 (SU)
    OFF
    Below 1 Ω
    1 (D) - 2 (SD)
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - REAR MOTOR RH)

B173122E03

  1. Disconnect the O5 switch connector.

  1. Disconnect the O3 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for Double Cab: 
    Tester Connection
    Condition
    Specified Condition
    O5-1 (D) - O3-2
    Always
    Below 1 Ω
    O5-4 (U) - O3-1
    O5-1 (D) or O3-2 - Body ground
    Always
    10 kΩ or higher
    O5-4 (U) or O3-1 - Body ground
    for CrewMax: 
    Tester Connection
    Condition
    Specified Condition
    O5-1 (D) - O3-1
    Always
    Below 1 Ω
    O5-4 (U) - O3-2
    O5-1 (D) or O3-1 - Body ground
    Always
    10 kΩ or higher
    O5-4 (U) or O3-2 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
B161800E01
  1. Remove the motor (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    for Double Cab: 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise
    for CrewMax: 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH RH)

B173123E03

  1. Disconnect the N2 master switch connector.

  1. Disconnect the O5 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-10 (U) - O5-5 (SU)
    Always
    Below 1 Ω
    N2-18 (D) - O5-2 (SD)
    N2-10 (U) or O5-5 (SU) - Body ground
    Always
    10 kΩ or higher
    N2-18 (D) or O5-2 (SD) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
B166136E04
  1. Remove the master switch (Click here).

  1. Reconnect the master switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N2-10 (U) - N2-1 (E)
    Ignition switch ON, rear RH side door power window regulator switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-18 (D) - N2-1 (E)
    Ignition switch ON, rear RH side door power window regulator switch OFF → DOWN



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL (Click here)