Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2UZ-FE)

DTC    P0781    1-2 Shift (1-2 Shift Valve)

for Preparation Click here


DESCRIPTION


  1. The 1-2 shift valve performs shifting to 1st gear and other gears.

    C159070E02


    DTC Code
    DTC Detection Condition
    Trouble Area
    P0781
    Gear required by the ECM does not match the actual gear when driving. (2 trip detection logic)
    1. Valve body is blocked up or stuck (1-2 shift valve)
    2. Shift solenoid valve SLT remains open or closed
    3. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the direction that the spring compresses.
The ECM commands gear shifts by turning the shift solenoid valves ON/OFF and controls the oil pressure applied to the valves in the valve body.
The ECM calculates the actual transmission gear by comparing the signals from the input speed sensor NT and the output speed sensor SP2. The ECM can detect mechanical problems in the shift solenoids, valve body and automatic transmission (clutch, brake, gear, etc.). If the ECM detects that the actual gear position and the commanded gear position are different, it will illuminate the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0781: Valve body/Rationality check
Required sensors/Components
Valve body, Automatic transmission assembly, Speed sensor (NT), Speed sensor (SP2), Vehicle speed sensor, Throttle position sensor
Frequency of operation
Continuous
Duration
Condition (A) and (B):
0.4 seconds
Condition (C):
3 seconds
Condition (D):
0.5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
None
Turbine speed sensor circuit
Not circuit malfunction
Output speed sensor circuit
Not circuit malfunction
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Shift solenoid valve SL1 circuit
Not circuit malfunction
Shift solenoid valve SL2 circuit
Not circuit malfunction
ECT (Engine Coolant Temperature) sensor circuit
Not circuit malfunction
KCS sensor circuit
Not circuit malfunction
ETCS (Electric Throttle Control System)
Not system down
Transmission position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or more
Spark advance from max. retard timing by KCS control
0° crankshaft angle or more
Engine
Starting

Condition (A) 
ECM selected gear
2nd
Vehicle speed
2 km/h (1.2 mph) or more
Output speed
2nd → 1st down shift point or more
Throttle valve opening angle
2% or more at 1000 rpm
(Conditions vary with engine speed)

Condition (B) 
ECM selected gear
4th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
2% or more at 1000 rpm
(Conditions vary with engine speed)

Condition (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed
(During transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

Condition (D) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
(After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed
(After transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: Condition (A) and Condition (B), (C) or (D)

Condition (A) 
Turbine speed/Output speed (NT/NO)
3.30 or more, and 7.50 or less
(This means actual gear is 1st)

Condition (B) 
Turbine speed/Output speed (NT/NO)
1.28 or more, and 1.53 or less
(This means actual gear is 3rd)

Condition (C) 
Turbine speed - Output speed x 4th gear ratio
(NT - NO x 4th gear ratio)
1000 rpm or more

Condition (D) 
Turbine speed - Output speed x 5th gear ratio
(NT - NO x 5th gear ratio)
1000 rpm or more

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0781)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0781 is output
    A
    P0781 and other DTCs are output
    B

    HINT:
    If any other codes besides P0781 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)

CAUTION:
This test should always be performed with at least 2 people.

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Perform the test with the A/C turned off.

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  1. Clear the DTC (Click here).

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the Techstream.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    ECT: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (31 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shift must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the Data List display on the Techstream.

    OK:
    Gear position changes in accordance with the Techstream command.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C159068E01
  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

  1. Measure the line pressure.

    ECT: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


4.CLEAR DTC AND PERFORM RUNNING TEST
  1. Clear the DTC (Click here).

  1. Check for DTC again after conducting the MONITOR DRIVE PATTERN (Click here).

    OK:
    No DTC code output.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

END