Home › ENGINE ยท 1GR-FE › FUEL › FUEL PUMP

FUEL PUMP > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. Some systems need to be initialized after the cable is reconnected (Click here).
    2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



    A159706
  1. Disconnect the 2 fuel pump ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the 2 fuel pump ECU connectors.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



3. REMOVE FUEL TANK CAP


4. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


A152240E01
  1. Detach the lock claw by lifting up the cover, as shown in the illustration.

  1. Pinch and pull the main tube connector to disconnect the connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



5. DISCONNECT FUEL TANK RETURN TUBE


A159750E01
  1. Detach the lock claw by lifting up the cover, as shown in the illustration.

  1. Pinch and pull the return tube connector to disconnect the connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



6. DISCONNECT VENT LINE HOSE


    A152244E01
  1. Pull up the retainer and disconnect the vent line hose.

    NOTICE:
    1. Do not use any tools in this procedure.
    1. Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.



7. DISCONNECT WIRE HARNESS


    A152242
  1. Detach the harness clamp from the fuel tank.



8. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


A152252E01
  1. Detach the lock claw by lifting up the cover, as shown in the illustration.

  1. Disconnect the fuel tank breather tube from the inlet pipe.

  1. Disconnect the fuel tank to filler pipe hose from the inlet pipe.

  1. Detach the filler pipe hose and breather tube from the No. 1 breather tube clamp.



9. DISCONNECT NO. 1 CANISTER OUTLET HOSE
  1. Disconnect the canister outlet hose from the inlet pipe.

  1. Detach the hose from the No. 1 breather tube clamp.



10. REMOVE FUEL TANK ASSEMBLY
  1. Set a mission jack underneath the fuel tank.



    A152248
  1. Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.

  1. Slowly lower the mission jack slightly.

    NOTICE:
    Be careful not to cut the wirings.



    A152243
  1. Detach the wire harness clamp from the fuel tank as shown in the illustration.

  1. Disconnect the fuel pump connector and lower the mission jack.

    NOTICE:
    1. Before this procedure, check the connector for dirt, mud or other contamination.
    2. Do not use any tools in this procedure.



11. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    A152246E01
  1. Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.



    A152237E01
  1. Using SST, loosen the retainer.

    SST
    09808-14020  

    HINT:
    Fit the tips of SST onto the ribs of the retainer.

    NOTICE:
    1. When the retainer is loosened, be careful as the pump and gauge tube will spring upward from the force of the spring.
    2. Clean the pump and gauge tube before this operation.

  1. Remove the retainer.

  1. Remove the fuel suction with pump and gauge tube assembly from the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.