Home › ENGINE ยท 3UR-FE › FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Apply a light coat of gasoline or grease to a new gasket, and install it to the fuel tank.



    A152236E01
  1. Align the protrusion of the pump and gauge tube with the groove of the fuel tank.

  1. Install the fuel suction with pump and gauge tube into the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Put the retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.



    A156395E01
  1. Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank, as shown in the illustration.

    SST
    09808-14020  

    HINT:
    Fit the tips of SST onto the ribs of the retainer.



    A152247
  1. Install the 2 fuel tank tubes with the 2 tube joint clips.

    NOTICE:
    A118171E02
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the tube joint clips are on the collars of the fuel tube joints.
    4. After installing the tube joint clips, check that the fuel tube joints have not been pulled off.



2. INSTALL FUEL TANK TO FILLER PIPE HOSE


    A152251
  1. Install the filler pipe hose to the fuel tank.



3. INSTALL NO. 1 FUEL TANK HEAT INSULATOR


    A152250E01
  1. Install the heat insulator with the 4 clips and nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



4. INSTALL INLET FUEL TANK PIPE SUB-ASSEMBLY


    A156396
  1. Install the inlet pipe with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



5. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank on a mission jack and raise the fuel tank.



    A152243
  1. Connect the harness clamp and fuel pump connector to the fuel tank.

    NOTICE:
    Be careful not to cut the wirings.

  1. Raise the mission jack.

  1. Install the 2 fuel tank bands with the 2 pins and 2 clips.



    A159722
  1. Connect the 2 fuel tank bands with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. CONNECT OUTLET NO. 1 CANISTER HOSE


A152253E01
  1. Connect the outlet canister hose to the inlet pipe.

  1. Attach the hose to the No. 1 breather tube clamp.



7. CONNECT FUEL TANK TO FILLER PIPE HOSE
  1. Connect the fuel tank to filler pipe hose to the inlet pipe.

  1. Connect the fuel tank breather tube to the inlet pipe.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.

  1. Attach the filler pipe hose and breather tube to the No. 1 breather tube clamp.



8. CONNECT WIRE HARNESS


    A152242
  1. Attach the harness clamp to the fuel tank.



9. CONNECT VENT LINE HOSE


    A152245
  1. Connect the vent line hose and install the retainer.

    NOTICE:
    1. Before installing the hose, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.
    1. After connecting, check if the hose and the connector are securely connected by pulling on them.



10. CONNECT FUEL TANK RETURN TUBE


A159751E01
  1. Connect the fuel tank return tube.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.



11. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A152241E01
  1. Connect the fuel tank main tube.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.



12. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)
  1. Install the tank protector with the 2 bolts and 2 nuts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for nut:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



13. INSTALL FUEL TANK CAP


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



15. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch ON.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.