FUEL TANK > INSTALLATION |
| 1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Apply a light coat of gasoline or grease to a new gasket and install it to the fuel tank.
![]() |
Align the protrusion of the fuel suction with pump and gauge tube assembly with the groove of the fuel tank.
Install the fuel suction with pump and gauge tube assembly into the fuel tank.
Put the retainer on the fuel tank. While holding the fuel suction with pump and gauge tube assembly, tighten the retainer one complete turn by hand.
![]() |
Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank, as shown in the illustration.
| 2. INSTALL FUEL TANK TO FILLER PIPE HOSE |
![]() |
Install the filler pipe hose to the fuel tank.
| 3. INSTALL NO. 1 FUEL TANK HEAT INSULATOR |
![]() |
Install the heat insulator with the 4 clips and nut.
| 4. INSTALL FUEL PRESSURE SWITCHING VALVE ASSEMBLY |
![]() ![]() |
Install the fuel pressure switching valve assembly with the 2 tube joint clips.
| 5. INSTALL FUEL TANK RETURN TUBE |
![]() ![]() |
Install the fuel tank return tube with the tube joint clip.
| 6. INSTALL INLET FUEL TANK PIPE SUB-ASSEMBLY |
![]() |
Install the inlet pipe with the 2 nuts.
| 7. INSTALL FUEL TANK ASSEMBLY |
Set the fuel tank on a transmission jack and raise the fuel tank.
![]() |
Connect the wire harness clamp, fuel pump connector and fuel pressure switching valve connector to the fuel tank assembly.
Raise the transmission jack.
Install the 2 fuel tank bands with the 2 pins and 2 clips.
![]() |
Connect the 2 fuel tank bands with the 2 bolts.
| 8. CONNECT OUTLET NO. 1 CANISTER HOSE |
![]() |
Connect the outlet canister hose to the inlet pipe.
Attach the hose to the No. 1 breather tube clamp.
| 9. CONNECT FUEL TANK TO FILLER PIPE HOSE |
Connect the fuel tank to filler pipe hose to the inlet pipe.
Connect the fuel tank breather tube to the inlet pipe.
Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.
Attach the filler pipe hose and breather tube to the No. 1 breather tube clamp.
| 10. CONNECT WIRE HARNESS |
![]() |
Attach the harness clamp to the fuel tank.
| 11. CONNECT VENT LINE HOSE |
![]() |
Connect the vent line hose and push down on the retainer.
| 12. CONNECT FUEL TANK RETURN TUBE |
![]() |
Connect the fuel tank return tube.
Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.
| 13. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
![]() |
Connect the fuel tank main tube.
Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.
| 14. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles) |
Install the tank protector with the 2 bolts and 2 nuts.
![]() |
Connect the fuel pressure switching valve with the bolt.
| 15. INSTALL FUEL TANK CAP |
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. INSPECT FOR FUEL LEAK |
Connect the Techstream to the DLC3.
Turn the ignition switch to on and Techstream main switch on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.