NAVIGATION SYSTEM (for Double Cab) > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the navigation receiver, steering pad switch, glove box light or other parts (seat heater switch, room light switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except navigation receiver. | B |
| No illumination (navigation receiver, glove box light, room light switch, etc.) comes on. | C |
| Illumination comes on for all components except steering pad switch and navigation receiver. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER AND BATTERY) |
![]() |
Disconnect the J45 cable connector.
Disconnect the K21 receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J45-4 (EAU) - K21-6 (SWG) | Always | Below 1 Ω |
| J45-4 (EAU) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J45-12 (IL+2) - Body ground | Light control switch OFF | Below 1 V |
| Light control switch TAIL or HEAD | 11 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |

Disconnect the z3 switch connector.
Connect the positive (+) lead to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch connector.
Check if the illumination for the steering pad switch comes on.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE |
![]() |
Disconnect the z3 and J45 cable connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-5 (IL+2) - J45-12 (IL+2) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise | ||
| z3-8 (EAU) - J45-4 (EAU) | Spiral cable is turned 2.5 rotations counterclockwise | |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY) |
![]() |
Disconnect the K18 receiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K18-2 (ILL+) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| Light control switch OFF | Below 1 V |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMBINATION METER) |
![]() |
Disconnect the K18 display connector.
Disconnect the J28 meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K18-12 (ILL-) - J28-37 (ILL-) | Always | Below 1 Ω |
| K18-12 (ILL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||