Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for CrewMax)

NAVIGATION SYSTEM (for CrewMax) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the illumination circuit for the navigation receiver and steering pad switch when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E138076E01


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the PRECAUTION in the Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver, steering pad switch, glove box light or other parts (seat heater switch, room light switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.

    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except navigation receiver.
    B
    No illumination (navigation receiver, glove box light, room light switch, etc.) comes on.
    C
    Illumination comes on for all components except steering pad switch and navigation receiver.
    D



B
Go to step 5

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 6
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER AND BATTERY)
E138073E02
  1. Disconnect the J45 cable connector.

  1. Disconnect the K21 receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J45-4 (EAU) - K21-6 (SWG)
    Always
    Below 1 Ω
    J45-4 (EAU) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J45-12 (IL+2) - Body ground
    Light control switch OFF
    Below 1 V
    Light control switch TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY

E138075E01

  1. Disconnect the z3 switch connector.

  1. Connect the positive (+) lead to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch connector.

  1. Check if the illumination for the steering pad switch comes on.

    OK:
    Illumination for the steering pad switch comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE
C152441E06
  1. Disconnect the z3 and J45 cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-5 (IL+2) - J45-12 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z3-8 (EAU) - J45-4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the PRECAUTION for the supplemental restraint system (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY)


    E138077E01
  1. Disconnect the K18 receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K18-2 (ILL+) - Body ground
    Light control switch
    TAIL or HEAD
    11 to 14 V
    Light control switch OFF
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMBINATION METER)


    E138078E01
  1. Disconnect the K18 display connector.

  1. Disconnect the J28 meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K18-12 (ILL-) - J28-37 (ILL-)
    Always
    Below 1 Ω
    K18-12 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)