Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for CrewMax)

NAVIGATION SYSTEM (for CrewMax) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the navigation receiver.
If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the navigation system cannot be operated using the steering pad switch, and the navigation system itself cannot function.

WIRING DIAGRAM


E138072E01


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the PRECAUTION in the Supplemental Restraint System (Click here).

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - SPIRAL CABLE)


    E138073E01
  1. Disconnect the K21 receiver connector.

  1. Disconnect the J45 cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K21-8 (SW2) - J45-5 (AU2)
    Always
    Below 1 Ω
    K21-6 (SWG) - J45-4 (EAU)
    K21-7 (SW1) - J45-6 (AU1)
    K21-8 (SW2) - Body ground
    Always
    10 kΩ or higher
    K21-6 (SWG) - Body ground
    K21-7 (SW1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SPIRAL CABLE
C152441E04
  1. Disconnect the z3 and J45 cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J45-4 (EAU) - z3-8 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    J45-5 (AU2) - z3-9 (AU2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    J45-6 (AU1) - z3-10 (AU1)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the PRECAUTION for the supplemental restraint system (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY

E138074E01

  1. Disconnect the z3 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (AU2) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    MODE switch pushed
    Below 1 Ω
    On Hook switch pushed
    329 Ω
    Off Hook switch pushed
    1000 Ω
    Voice switch is pushed
    3110 Ω
    10 (AU1) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    Seek+ switch pushed
    Below 1 Ω
    Seek- switch pushed
    329 Ω
    Volume+ switch is pushed
    1000 Ω
    Volume- switch is pushed
    3110 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)