Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Regular Cab and Double Cab)

AUDIO AND VISUAL SYSTEM (for Regular Cab and Double Cab) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM


E146424E01


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).

1.INSPECT RADIO RECEIVER


    B109191E04
  1. Disconnect the K3 receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K3-7 (SW1) - K3-6 (SWG)
    No switch is pushed
    100 kΩ or higher
    Seek+ switch: push
    Below 1 Ω
    Seek- switch: push
    329 Ω
    Volume+ switch: push
    1000 Ω
    Volume- switch: push
    3100 Ω
    K3-8 (SW2) - K3-6 (SWG)
    No switch is pushed
    100 kΩ or higher
    MODE switch: push
    Below 1 Ω
    On Hook switch: push
    329 Ω
    Off Hook switch: push
    1000 Ω



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the z3 switch connector.



  1. Measure the resistance according to the values in the table below.


    E145917E01


    Standard resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    z3-10 (AU1) - z3-8 (EAU)
    No switch is pushed
    100 kΩ or higher
    Seek+ switch: push
    Below 1 Ω
    Seek- switch: push
    329 Ω
    Volume+ switch: push
    1000 Ω
    Volume- switch: push
    3110 Ω
    z3-9 (AU2) - z3-8 (EAU)
    No switch is pushed
    100 kΩ or higher
    MODE switch: push
    Below 1 Ω
    On Hook switch: push
    329 Ω
    Off Hook switch: push
    1000 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3.INSPECT SPIRAL CABLE


    C152441E04
  1. Disconnect the z3 switch connector.

  1. Disconnect the J45 cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - J45-4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z3-10 (AU1) - J45-6 (AU1)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z3-9 (AU2) - J45-5 (AU2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the PRECAUTION for the SRS (Click here).



NG
REPLACE SPIRAL CABLE (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)