DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
DTC P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 | Calculated value of air-fuel ratio (A/F) sensor response rate deterioration level less than threshold (2 trip detection logic) |
|
| P2A03 | Calculated value of air-fuel ratio (A/F) sensor response rate deterioration level less than threshold (2 trip detection logic) |
|


| Related DTCs | P2A00: Air-Fuel Ratio (A/F) sensor slow response (Bank 1) P2A03: Air-Fuel Ratio (A/F) sensor slow response (Bank 2) |
| Required Sensors/Components (Main) | A/F sensor |
| Required Sensors/Components (Related) | Vehicle speed sensor, Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 to 15 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater) P0102, P0103 (Mass Air Flow Sensor) P0112, P0113 (Intake Air Temperature Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel System) P0301 - P0308 (Misfire) P0335 (Crankshaft Position Sensor) P1340 (Camshaft Position Sensor) P0451, P0452, P0453 (EVAP System) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control) P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System) P0500, P0722 (Vehicle Speed Sensor) P0505 (IAC Valve) |
| Active A/F control | Performing |
| Active A/F control performed when following conditions met | - |
| Engine coolant temperature | 75°C (167°F) or more |
| Battery voltage | 11 V or more |
| Idle | OFF |
| Engine speed | Less than 4000 rpm |
| A/F sensor status | Activated |
| Fuel-cut | OFF |
| Engine load | 10 to 70% |
| Shift position | 2nd or more |
| Catalyst monitor | Not yet |
| Intake air amount | 2.5 to 12 g/sec. |
| Response rate deterioration level | Less than 0.2 V |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2A00 and/or P2A03 are output | A |
| P2A00 and/or P2A03 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the D33 or D34 A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HA1A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA1A) - 4 (A1A-) | Always | 10 kΩ or higher |
| 1 (HA2A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA2A) - 4 (A2A-) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - AIR-FUEL RATIO SENSOR) |
![]() |
Disconnect the D33 or D34 A/F sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D33-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D34-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D33-1 (HA1A) - D74-22 (HA1A) | Always | Below 1 Ω |
| D33-3 (A1A+) - D74-126 (A1A+) | Always | Below 1 Ω |
| D33-4 (A1A-) - D74-125 (A1A-) | Always | Below 1 Ω |
| D34-1 (HA2A) - D74-20 (HA2A) | Always | Below 1 Ω |
| D34-3 (A2A+) - D74-103 (A2A+) | Always | Below 1 Ω |
| D34-4 (A2A-) - D74-102 (A2A-) | Always | Below 1 Ω |
| D33-1 (HA1A) or D74-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D33-3 (A1A+) or D74-126 (A1A+) - Body ground | Always | 10 kΩ or higher |
| D33-4 (A1A-) or D74-125 (A1A-) - Body ground | Always | 10 kΩ or higher |
| D34-1 (HA2A) or D74-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
| D34-3 (A2A+) or D74-103 (A2A+) - Body ground | Always | 10 kΩ or higher |
| D34-4 (A2A-) or D74-102 (A2A-) - Body ground | Always | 10 kΩ or higher |

|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| P2A00 and/or P2A03 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 6.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P2A00 and/or P2A03 are output | B |
|
| ||||
| A | ||
| ||