DTC P1613 Secondary Air Injection Driver Malfunction |
DTC P1614 Secondary Air Injection System Driver Bank 2 |
| DTC Code | DTC Detection Condition | Trouble Area |
| P1613 P1614 | Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):
|
|
| P1613 P1614 |
|
|
| P1613 P1614 |
|
|
| Related DTCs | P1613: Secondary air injection system air injection control driver circuit range check P1614: Secondary air injection system air injection control driver circuit range check |
| Required Sensors/Components (Main) | Air injection control driver |
| Required Sensors/Components (Related) | Air switching valve |
| Frequency of Operation | Once per drive cycle |
| Duration | 3 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| Monitor runs whenever following DTCs not present | None |
| Either a or b met: | - |
| a. Air pump | Not operating |
| b. Air switching valve | Not operating |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| Monitor runs whenever following DTCs not present | None |
| Following conditions (a) and (b) met | - |
| a. Air pump | Operating |
| b. Air switching valve | Operating |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| One of following conditions met: | A, B, C or D |
| A. Diagnostic signal duty ratio from air injection control driver | 1% or more, and 10% or less |
| B. Diagnostic signal duty ratio from air injection control driver | 30% |
| C. Diagnostic signal duty ratio from air injection control driver | 49% |
| D. Diagnostic signal duty ratio from air injection control driver | 91% or more, and 99% or less |
| Diagnostic signal duty ratio from air injection control driver | 70% or more, and 90% or less |
| Diagnostic signal duty ratio from air injection control driver | 0% |
| Diagnostic signal duty ratio from air injection control driver | 100% |
| Diagnostic signal duty ratio from air injection control driver | 70% or more, and 90% or less when secondary air injection system operating. 0% when secondary air injection system not operating. |
| AID Diagnostic Signal Waveforms | ECM Commands | DTCs (ECM Output) | Suspected Trouble Areas |
100% Duty Ratio![]() | Any Secondary Air Injection (AIR) System operation | P1613 P1614 |
|
0% Duty Ratio![]() | AIR System: ON (Air pump ON, ASV ON) | P1613 P1614 |
|
| AIR System: OFF (Air pump OFF, ASV OFF) | - | Normal | |
20% Duty Ratio![]() | Air Pump: ON | P0418 P0419 |
|
| Air Pump: OFF | P0418 P0419 |
| |
40% Duty Ratio![]() | ASV: ON | P0412 P0415 |
|
| ASV: OFF | P0412 P0415 |
| |
80% Duty Ratio![]() | AIR System: OFF (Air pump OFF, ASV OFF) | P1613 P1614 |
|
| AIR System: ON (Air pump ON, ASV ON) | - | Normal | |
| Other than above (other than 0, 20, 40, 80 and 100% duty) | - | P1613 P1614 |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613 OR P1614) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P1613 and/or P1614 are output | A |
| P1613 and/or P1614 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the D50 or D54 AID connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D50-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
| D54-5 (+B2) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AID - ECM, BODY GROUND) |
![]() |
Disconnect the A24 or D74 ECM connector.
Disconnect the D50 or D54 AID connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-54 (AIRP) - D50-4 (SIP) | Always | Below 1 Ω |
| D74-28 (AIRV) - D50-3 (SIV) | Always | Below 1 Ω |
| D74-53 (ARP2) - D54-4 (SIP2) | Always | Below 1 Ω |
| A24-43 (ARV2) - D54-3 (SIV2) | Always | Below 1 Ω |
| D74-30 (AIDI) - D50-2 (DI) | Always | Below 1 Ω |
| D74-29 (AID2) - D54-2 (DI2) | Always | Below 1 Ω |
| D50-1 (E) - Body ground | Always | Below 1 Ω |
| D54-1 (E2) - Body ground | Always | Below 1 Ω |
| D74-54 (AIRP) or D50-4 (SIP) - Body ground | Always | 10 kΩ or higher |
| D74-28 (AIRV) or D50-3 (SIV) - Body ground | Always | 10 kΩ or higher |
| D74-53 (ARP2) or D54-4 (SIP2) - Body ground | Always | 10 kΩ or higher |
| A24-43 (ARV2) or D54-3 (SIV2) - Body ground | Always | 10 kΩ or higher |
| D74-30 (AIDI) or D50-2 (DI) - Body ground | Always | 10 kΩ or higher |
| D74-29 (AID2) or D54-2 (DI2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE) |
![]() |
Disconnect the D50 or D54 AID connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D50-2 (DI) - D50-1 (E) | Ignition switch ON | 11 to 14 V (near battery voltage) |
| D54-2 (DI2) - D54-1 (E2) | Ignition switch ON | 11 to 14 V (near battery voltage) |
|
| ||||
| OK | |
| 5.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 6.CONFIRM WHETHER DTC OUTPUT RECURS |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Clear DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing Next.
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Result | Proceed To |
| No DTC is output | A |
| Other DTCs are output | B |
Turn the ignition switch off.
|
| ||||
| A | ||
| ||