Home › ENGINE ยท 1GR-FE › COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A072954E01
  1. Install a new gasket and the water pump with the 17 bolts.

    Torque:
    for 10 mm head:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    for 12 mm head:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



2. INSTALL GENERATOR ASSEMBLY


    A152257
  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A152256
  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the wire harness clamp to the bracket.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the generator connector.



    A152255
  1. Install the wire harness clamp bracket with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A076445E04
  1. Temporarily install the V-ribbed belt tensioner with the 5 bolts.

  1. Install the V-ribbed belt tensioner by tightening bolt 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

    Bolt length:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)



4. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

NOTICE:
The installation of the No. 2 idler pulleys differs depending on the mark on the No. 2 idler pulleys shown in the illustration.

A191316E01

HINT:
Use the same procedure for both No. 2 idler pulleys.



  1. w/ Idler Pulley Cover Plate (PU107013ARMXY3):



      A191314E01
    1. Install the idler pulley cover plate, idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      1. If it is necessary to replace the pulley or either plate, replace the No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate as a set with new parts.
      2. When replacing parts, make sure to replace the No. 2 idler pulley with a new pulley marked "PU107013ARMXY3".



  1. w/o Idler Pulley Cover Plate (PU107013ARMXY1):



      A191315E01
    1. Install the idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      1. If it is necessary to replace the pulley or plate, replace both the pulley and plate with a set of new parts that includes a No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate.
      2. When replacing parts, make sure to replace the No. 2 idler pulley with a new pulley marked "PU107013ARMXY3".



5. INSTALL WATER INLET HOUSING


A076340E03
  1. Install a new gasket to the water outlet pipe.

  1. Install a new gasket to the water pump.

  1. Apply soapy water to the gasket labeled A shown in the illustration.



    A076337E02
  1. Install the water inlet with the 5 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    A151853E01
  1. Connect the 5 water by-pass hoses.



    A151852E01
  1. Connect the 2 oil cooler hoses.



6. INSTALL FAN SHROUD
  1. Install the fan pulley to the water pump.

  1. Place the shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.



    A151756
  1. Attach the shroud's claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the radiator tank upper.

  1. Install the fan and generator V-belt (Click here).

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



7. CONNECT RADIATOR HOSE INLET


8. CONNECT RADIATOR HOSE OUTLET


9. INSTALL AIR CLEANER ASSEMBLY WITH ELEMENT


    A151811E01
  1. Install the air cleaner with element with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the hose clamp.

    HINT:
    Tighten the hose clamp until it reaches the specified protrusion height labeled A shown in the illustration.

    Standard protrusion height:
    Below 0.5 mm (0.0197 in.)



    A151769
  1. Connect the MAF meter connector.

  1. Attach the 2 wire harness clamps.

  1. Connect the vacuum hose.



    A151812
  1. Attach the hose clamp.

  1. Connect the No. 2 ventilation hose.



10. INSTALL NO. 2 AIR CLEANER HOSE


A161774E01

HINT:
Securely insert the pin of the No. 2 air cleaner hose into the grommet.



    A151855E01
  1. Install the air cleaner hose with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Tighten the hose clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Tighten the clamp until the end of the clamp band is within both limit marks.



11. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    9.6 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E01
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E03
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



12. INSPECT FOR COOLANT LEAK


A151851

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



13. INSTALL V-BANK COVER


    A112983E02
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



14. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the engine under cover with the 5 bolts and 3 screws.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }