Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for CrewMax)

NAVIGATION SYSTEM (for CrewMax) > DIAGNOSIS DISPLAY DETAILED DESCRIPTION

for Preparation Click here


HINT:
  1. This section contains a detailed description of displays within diagnostic mode.
  2. Illustrations may differ from the actual vehicle depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle.


SYSTEM CHECK


  1. System Check Mode Screen


    E146288E01


    1. Device Names and Hardware Address/*1

      HINT:
      1. Registered device names are displayed.
      2. If a device name is unknown to the system, its physical address is shown instead.

      Address No.
      Name
      Address No.
      Name
      110
      EMV
      120
      AVX
      128
      1DIN TV
      140
      AVN
      144
      G-BOOK
      178
      NAVI
      17C
      MONET
      190
      AUDIO
      1AC
      CAMERA-C
      1B0
      Rr-TV
      1C0
      Rr-CONT
      19D
      BT-HF
      1C4
      PANEL
      1C6
      G/W
      1C8
      FM-M-LCD
      1D8
      CONT-SW
      1EC
      BODY
      118
      EMVN
      1F1
      XM
      1F2
      SIRIUS
      230
      TV
      240
      CD-CH2
      250
      DVD-CH
      280
      CAMERA
      360
      CD-CH1
      3A0
      MD-CH
      17D
      TEL
      440
      DSP-AMP
      530
      ETC
      1F6
      RSE
      1A0
      DVD-P
      1D6
      CLOCK
      238
      DTV
      480
      AMP

    2. Check Result/*2

      HINT:
      Result codes for all devices are displayed.

      Result
      Meaning
      Action
      OK
      Device did not respond with DTC (excluding communication DTCs from AVC-LAN).
      -
      EXCH
      Device responds with "replace" type DTC.
      Look up DTC in "Unit Check Mode" and replace device.
      CHEK
      Device responds with "check" type DTC.
      Look up DTC in "Unit Check Mode".
      NCON
      Device was previously present, but does not respond in diagnostic mode.
      1. Check power supply wire harness of device.
      2. Check AVC-LAN of device.
      Old
      Device responds with "old" type DTC.
      Look up DTC in "Unit Check Mode".
      NRES
      Device responds in diagnostic mode, but gives no DTC information.
      1. Check power supply wire harness of device.
      2. Check AVC-LAN of device.

    3. Code Clear/*3

      1. Present DTCs are cleared.
      2. Press the "Code CLR" switch for 3 seconds.

    4. Memory Clear/*4

      1. Present and past DTCs and registered connected device names are cleared.
      2. Press the "Memory CLR" switch for 3 seconds.



  2. Diagnosis MENU Screen


    E120070E01

    HINT:
    Some items may be grayed out or not displayed, as the functions are different depending on the vehicle.



  3. Unit Check Mode Screen


    E136182E02


    Screen description: 
    Display
    Contents
    Device name/*1
    Target device
    Segment/*2
    Target device logical address
    DTC/*3
    DTC (Diagnostic Trouble Code)
    Timestamp/*4
    Time and date of past DTCs are displayed (year is displayed in 2-digit format).
    Present Code/*5
    DTCs output at service check are displayed.
    Past Code/*6
    Diagnostic memory results and recorded DTCs are displayed.
    Diagnosis Clear Switch/*7
    Pushing this switch for 3 seconds clears diagnostic memory data of target device (response to diagnostic system check result and displayed data are cleared).



  4. LAN Monitor (Original) Screen


    E146289E01


    1. Check Result/*

      HINT:
      Check results of all the devices are displayed.

      Result
      Meaning
      Action
      No Err (OK)
      There are no communication DTCs.
      -
      CHEK
      Device responds with "check" type DTC.
      Look up DTC in "Unit Check Mode".
      NCON
      Device was previously present, but does not respond in diagnostic mode.
      1. Check power supply wire harness of device.
      2. Check AVC-LAN of device.
      Old
      Device responded with "old" type DTC.
      Look up DTC in "Unit Check Mode".
      NRES
      Device responds in diagnostic mode, but gives no DTC information.
      1. Check power supply wire harness of device.
      2. Check AVC-LAN of device.



  5. LAN Monitor (Individual) Screen


    E136184E02


    Screen description: 
    Display
    Contents
    Device name/*1
    Target device
    Segment/*2
    Target logical address
    DTC/*3
    DTC (Diagnostic Trouble Code)
    Sub-code (device address)/*4
    Physical address stored with DTC (If there is no address, nothing is displayed).
    Connection check No./*5
    Connection check number stored with DTC
    DTC occurrence/*6
    Number of times same DTC has been recorded
    Diagnosis Clear Switch/*7
    Pushing this switch for 3 seconds clears diagnostic memory data of target device (response to diagnostic system check result and displayed data are cleared).


DISPLAY CHECK


  1. Vehicle Signal Check Mode Screen


    E146768


    Screen description: 
    Name
    Contents
    Battery
    Battery voltage is displayed.
    PKB
    Parking brake ON / OFF state is displayed.
    REV
    Reverse signal ON / OFF state is displayed.
    IG
    OFF is always displayed.
    TAIL
    TAIL signal (Light control switch) ON / OFF state is displayed.
    SPEED
    Vehicle speed is displayed in km/h.

    HINT:
    1. Only items sending a vehicle signal will be displayed.
    2. This screen is updated once per second when input signals to the vehicle are changed.


NAVIGATION CHECK


  1. Navigation Check Screen


    E120076E05

    HINT:
    Some items may be grayed out or not displayed, as the functions are different depending on the vehicle.



  2. GPS Information Screen


    E147753E01


    1. Satellite information/*1
      Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction, and signal level.

    2. Receiving condition/*2

      DENSO model: 
      Display
      Contents
      T
      System is receiving GPS signal, but is not using it for location.
      P
      System is using GPS signal for location.
      -
      System cannot receive GPS signal.

      AISIN AW model: 
      Display
      Contents
      01H
      System cannot receive a GPS signal.
      02H
      System is tracing a satellite.
      03H
      System is receiving a GPS signal, but is not using it for location.
      04H
      System is using the GPS signal for location.

      Measurement information/*3: 
      Display
      Contents
      2D
      2-dimensional location method is being used.
      3D
      3-dimensional location method is being used.
      NG
      Location data cannot be used.
      Error
      Reception error has occurred.
      -
      Any other state.

      Position information/*4 
      Display
      Contents
      Position
      Latitude and longitude information on current position is displayed.

      Date information/*5: 
      Display
      Contents
      Date
      Date / time information obtained from GPS signal is displayed in Greenwich mean time (GMT). Last 4 digits are displayed.



  3. Vehicle Sensors Screen


    E120077E01


    Vehicle signal: 
    Display
    Contents
    REV/*1
    REV signal ON/OFF state is displayed.
    SPD/*2
    SPD signal condition is displayed.

    Sensor signal: 
    Display
    Contents
    Gyro sensor/*3
    Gyro sensor output condition is displayed (when vehicle runs straight or is stationary, voltage is approximately 2.5 V).

    HINT:
    Signals are updated once per second only when vehicle sensor signals are changed.



  4. Microphone & Voice Recognition Check Screen


    E125119E01


    Screen description: 
    Display
    Contents
    Microphone input level meter/*1
    Monitors the microphone input level every 100 msec. and displays results in 8 different levels.
    Recording switch/*2
    Starts recording.
    Stop switch/*3
    Stops recording.
    Play switch/*4
    Plays recorded voice.
    Recording indicator/*5
    Comes on while recording.

    HINT:
    1. The microphone input function is on at all times when this screen is displayed.
    2. While recording or playing, the switches other than the stop switch cannot be pushed.
    3. When no voice is recorded, the play switch cannot be pushed.
    4. Recording will stop after 5 seconds or by pushing the stop switch.



  5. DVD Player Information Screen


    E120078E01


    Screen description: 
    Display
    Contents
    Trouble code/*1
    Each code corresponding to malfunctions is displayed. For details, refer to "Trouble Code Description".
    Occurrence time/*2
    1. Date (year, month, day) and time (hour, minute, second) when trouble code was detected are displayed as time stamp (Greenwich mean time).
    2. Time data to be displayed is received from GPS receiver.
    Trouble code clear switch/*3
    All code data being displayed is cleared by pushing this switch for 3 seconds.
    Returning switch/*4
    Previous page is displayed. If current displayed page is first page, this switch cannot be operated.
    Proceeding switch/*5
    Next page is displayed. If current displayed page is last page, this switch cannot be operated.

    Trouble code description: 
    Code
    Malfunction
    Countermeasure
    01
    Cannot be recognized
    Replace navigation receiver.
    03
    Cannot be read
    Follow inspection procedure for DTC 58-42 (Click here).

    HINT:
    This is a DVD player check function in the navigation receiver.