DTC B1783 Rear Occupant Classification Sensor RH Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1783 | One of following conditions is met:
|
|

| 1.CHECK FOR DTC |
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the rear occupant detection sensor RH.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Check that the connectors (on the occupant classification ECU side and rear occupant detection sensor RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH |
![]() |
Disconnect the connectors from the occupant classification ECU and the rear occupant detection sensor RH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Y1-4 (SGD4) - Body ground | Ignition switch ON | Below 1 V |
| Y1-6 (SVC4) - Body ground | ||
| Y1-10 (SIG4) - Body ground |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using service wires, connect terminals 1 (SVC4) and 3 (SGD4), and connect terminals 2 (SIG4) and 3 (SGD4) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y1-6 (SVC4) - Y1-4 (SGD4) | Always | Below 1 Ω |
| Y1-10 (SIG4) - Y1-4 (SGD4) |
Disconnect the service wires from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y1-6 (SVC4) - Y1-4 (SGD4) | Always | 1 MΩ or higher |
| Y1-10 (SIG4) - Y1-4 (SGD4) | ||
| Y1-6 (SVC4) - Y1-10 (SIG4) | ||
| Y1-4 (SGD4) - Body ground | ||
| Y1-6 (SVC4) - Body ground | ||
| Y1-10 (SIG4) - Body ground |
|
| ||||
| OK | |
| 5.CHECK FOR DTC |
Connect the connectors to the occupant classification ECU and the rear occupant detection sensor RH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU.
| NEXT | |
| 7.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch ON, and wait for at least 60 seconds.
Using the Techstream, perform the zero point calibration (Click here).
|
| ||||
| OK | |
| 8.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
|
| ||||
| OK | |
| 9.CHECK FOR DTC |
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 10.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat frame with adjuster RH (Click here).
| NEXT | |
| 11.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch ON, and wait for at least 60 seconds.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 12.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
| NEXT | ||
| ||