Home › ENGINE ยท 1GR-FE › FUEL › FUEL PRESSURE REGULATOR

FUEL PRESSURE REGULATOR > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. Some systems need to be initialized after the cable is reconnected (Click here).
    2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



    A159706
  1. Disconnect the 2 fuel pump ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the 2 fuel pump ECU connectors.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



3. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 5 bolts, 3 screws and engine under cover.



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151786E01

  1. Tighten the radiator drain cock plug by hand.



5. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
  1. Remove the front wiper motor and link (Click here).



6. REMOVE FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the 2 washer hoses.



  1. Remove the 7 bolts and front cowl top outer panel.


    A151796



7. REMOVE V-BANK COVER


    A112983E03
  1. Remove the 2 nuts and V-bank cover.



8. REMOVE NO. 2 AIR CLEANER HOSE


A151771
  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner hose.



9. REMOVE AIR CLEANER ASSEMBLY WITH ELEMENT


    A151812
  1. Disconnect the No. 2 ventilation hose.

  1. Detach the hose clamp.



    A151769
  1. Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Using a clip remover, detach the 2 wire harness clamps.



    A151770
  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner with element.



10. REMOVE INTAKE AIR SURGE TANK


    A151856
  1. Disconnect the throttle position sensor and throttle control motor connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.



    A151765
  1. Disconnect the purge line hose.

  1. Disconnect the purge VSV connector.

  1. Disconnect the union to check valve hose.



    A151766
  1. Disconnect the No. 1 ventilation hose.



    A151768
  1. Disconnect the vacuum switching valve (for ACIS) connector.

  1. Using a clip remover, detach the 2 wire harness clamps.



    A151767
  1. Remove the 2 bolts and throttle body bracket.



    A151773
  1. Using a clip remover, detach the wire harness clamp.

  1. Remove the bolt and oil baffle plate.



    A151772
  1. Remove the 2 bolts and No. 1 surge tank stay.

  1. Remove the 2 bolts and No. 2 surge tank stay.



    A075648E05
  1. Remove the 2 nuts.

  1. Using an 8 mm hexagon wrench, remove the 4 bolts. Then remove the intake air surge tank and gasket.



11. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY


    A159686E01
  1. Remove the fuel pipe clamp.

  1. Pinch the tube connector, and then pull the fuel pipe out of the pipe as shown in the illustration.

    NOTICE:
    1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Keep the plug free from foreign objects.
    6. Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube.
    7. If the fuel tube connector and pipe are stuck, push and pull to release them.



12. REMOVE FUEL PRESSURE REGULATOR ASSEMBLY


    A133700
  1. Remove the 2 bolts, then remove the fuel pressure regulator.

  1. Remove the O-ring from the fuel pressure regulator.

  1. Remove the vacuum hose.