FRONT DRIVE SHAFT ASSEMBLY (for 4WD) > INSTALLATION |
| 1. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for Front Differential Side) |
Install a new snap ring to the inboard joint shaft.
Coat the spline of the inboard joint shaft assembly with gear oil.
![]() |
Align the shaft splines and install the drive shaft with a brass bar and hammer.
| 2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for Axle Hub Side) |
Install the drive shaft to the steering knuckle.
| 3. CONNECT FRONT LOWER BALL JOINT ATTACHMENT |
![]() |
Connect the attachment to the steering knuckle with the 2 bolts.
| 4. INSTALL TIE ROD END SUB-ASSEMBLY |
Connect the tie rod end LH to the steering knuckle with the nut.
Install a new cotter pin.
| 5. INSTALL AXLE HUB NUT |
Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.
Using a 39 mm socket wrench, install the hub nut.
![]() |
Install the front wheel adjusting lock cap and a new cotter pin.
| 6. INSTALL FRONT AXLE HUB GREASE CAP |
Install the axle hub grease cap.
| 7. INSTALL FRONT SPEED SENSOR LH |
Install the front speed sensor (Click here).
| 8. INSTALL NO. 1 ENGINE UNDER COVER |
Install the engine under cover with the 5 bolts and 3 screws.
| 9. INSTALL FRONT WHEEL |
Install the front wheels.
| 10. ADD DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
| Item | Oil type and viscosity |
| Front differential | Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent. |
| Rear differential |
| Specified Condition | |
| 2.05 to 2.15 liters (2.2 to 2.3 US qts., 1.8 to 1.9 Imp. qts.) |
| Engine type | Wheelbase type | Cab type | Drive type | Specified Condition |
| 3UR-FE. 3UR-FBE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 3.40 to 3.50 liters (3.6 to 3.7 US qts., 3.0 to 3.1 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | Regular | 2WD | 3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.) | |
| 4WD | ||||
| Double | 2WD | |||
| 4WD | ||||
| CrewMax | 2WD | 3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.) | ||
| 4WD | 3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.) | |||
| 4180 mm (13 ft. 8.6 in.) | Double | 2WD | 3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.) | |
| 4WD | ||||
| 1GR-FE and 2UZ-FE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 4.00 to 4.10 liters (4.2 to 4.3 US qts., 3.5 to 3.6 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | ALL | 2WD | 4.55 to 4.65 liters (4.8 to 4.9 US qts., 4.0 to 4.1 Imp. qts.) | |
| 4WD | ||||
| 4180 mm (13 ft. 8.6 in.) | 2WD | |||
| 4WD |
for Rear Differential:
Install a new gasket and the filler plug.
for Front Differential:
Using a 10 mm hexagon wrench, install a new gasket and the filler plug.
| 11. CHECK SPEED SENSOR SIGNAL |
Check the speed sensor signal (Click here).
| 12. CHECK FOR DIFFERENTIAL OIL LEAK |
| 13. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
Inspect and adjust the front wheel alignment (Click here).